valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
The inner cover of the condenser unit has not been locked properly and/or the condenser unit has not been positioned correctly. Fluff has collected at – Ensure that the condenser unit is positioned correctly and lock the cover. – Check the rubber seals. – Use a cloth to remove anyWater leaks from the machine after the the bottom of the fluff from the inside of the condenser unit has condenser unit housing. condenser unit housing. been cleaned. Check and fault indicator lamps Problem Possible cause Remedy The Empty out The condensed water – Empty out the condensed container indicator container is full or there water container. lamp comes on. is kink in the drain hose. – Check the drain hose. – Before starting a new programme, first switch the dryer off and then on again. The programme has There is no obvious – Switch off the dryer. been interrupted, the cause. – Then switch the dryer back indicator lamp for on and start the programme Hand iron or Machine again. iron is flashing, and If the programme stops againthe buzzer sounds. and an indicator lamp flashes, there is a fault. Contact the Miele Service Department. Problem solving guide Problem Possible cause Remedy The programme has stopped, the Anti-crease/Finish lamp has come on in the sequence display and the buzzer is sounding. This is not a fault. The electronic unit has recognised that there is no laundry in the drum and cancelled the programme. Drying individual garments or items which are already dry can also cause the programme to be stopped. Use the "Timed drying Warm air" programme to dry individual items. Before changing a programme: Open and close the drum door. Problem solving guide Changing the lamp Disconnect the machine from the mains electricity supply. ^ Open the door. You will find the interior lamp cover at the top of the drum aperture. The lamp specification and maximum wattage is stated on the data plate and on the lamp cover. ^ Replace the lamp. ^ To close the cover push it upwards and press it on the left and right until you hear it click into position. ,Ensure that it is fitted into position securely, as any moisture could cause a short circuit. ^ Insert a suitable tool, such as a wide bladed screwdriver, under the side edge of the lamp cover as illustrated. ^ Apply a little pressure and whilst doing so turn your wrist in the direction of the arrow to open the cover. The cover will open downwards. The temperature resistant lamp should only be ordered from your Miele dealer or the Miele Spare Parts Department. After sales service Repairs In the event of any faults which you cannot remedy yourself, or if the machine is under guarantee, please contact – your Miele dealer, or – the Miele Service Department (see back cover for contact details). When contacting your Dealer or the Service Department, please quote the model and serial number of your machine, both of which are shown on the data plate situated on the right hand side below the drum aperture. Appliance guarantee Please see the guarantee card supplied with your machine. Optional accessories Optional accessories for this dryer is available from your Miele Dealer or from the Miele Spare Parts Department. Please note that telephone calls may be monitored and recorded to improve our service. Front view aMains connection cable bCondensed water container cControl panel dDoor eService panel for condenser unit fFour height-adjustable screw feet gExternal drainage options (e.g. via wash basin, wash basin drain outlet, or gully). Installation 29 Installation Installation site ,Make sure the dryer door can be opened without hindrance after installation. Transporting the machine to its installation site When moving the machine you can hold it by the lid where it protrudes to the rear of the dryer. To manoeuvre the dryer out of its packing case to its installation site you will also need to hold it by the front feet. Building under a continous worktop / in a row of kitchen units The dryer should not be installed next to a refrigerator or freezer. The warm air expelled from the rear of the dryer would increase the temperature around the refrigerator's/freezer's heat exchanger causing the compressor to run continuously. If it is not possible to install the dryer anywhere else, then the refrigerator/freezer must be sealed off from the dryer. If you wish to push your machine under a worktop and there is space to do this without removing the lid, a building under kit is not necessary. Otherwise the building under kit is essential. ,The building under kit* must be fitted by a suitably qualified person. The machine lid is replaced by a coverplate. It is essential that the coverplate is fitted to ensure electrical safety. The building under kit is supplied with its own installation instructions. N.B. When built under running times may be longer. – The electrical socket must be located in an accessible position near the machine. With niche heights of: – 840 mm, longer screw feet* are required. – 870/...