valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Fig.48 Removing the lid 57 Before you call for service Your AeroSmart dryer is capable of diagnosing its own troubles. If your dryer is displaying a message on the display screen and is sounding a musical series of beeps every 5 seconds, it has a problem that you may be able to solve using the checklist below. (It’s the same sound AeroSmart dryer makes when you plug it in). If you are unable to solve the problem from the checklist below call for service. Close the lid and press START/PAUSE. If the lid is already closed, open the lid and close it again, then press START/PAUSE. Disconnect from the power (either by unplugging the dryer or turning off the circuit Machine is beeping and … “I can’t LOCK THE LID” breaker that supplies it). Wait 10 seconds, reconnect and try turning it on again. EN Machine is beeping and… “I can’t CLOSE THE DRUM” The machine is unable to close the drum due to clothes interfering with the closing mechanism. Remove any articles that are interfering with the drum door and dry these in the next load. Is your load higher than the top of the lint bucket? Remove some articles and dry these in the next load. If your dryer is continually beeping and a message is displayed on the screen, a fault has occurred which requires repair from a Service Agent. Pressing the POWER button once will stop the beeping but will still display the fault code. We recommend leaving the machine in this mode as the fault code will enable the service person to quickly identify the cause of the problem. Single beep every second and … “I need SERVICE” message and fault number. 1. Turn your machine off at the wall. 2. Wait 1 minute and turn it back on. 3. Check your machine is level (refer to installation instructions pages 7 – 31). 4. Remove load and retry. 5. If the fault re-occurs repeat steps 1 and 2. If the machine still will not work, call your Fisher & Paykel Dealer or Authorised Service Agent to arrange service (refer to page 62). Solving operating problems Pressing POWER does not turn the dryer on Is the electrical cord plugged in? If not plug the cord in. If there is a switch, is it switched on? Could your household power supply be at fault? (If your plug is suitable, try plugging another electrical appliance into the same outlet). Check your house circuit breakers and fuses. If they are at fault contact an electrician. Dryer does not heat Is the dryer set to the AIR DRY cycle? Is the gas turned on? (Gas/LPG dryers only). Has the dryer progressed to COOLING. (Check the Display Screen). If the problem persists call for service. Clothes are still wet/damp Is the dryer set on DAMP? Try selecting a higher dryness level. Is the drum warm? If not, is the dryer set to the AIR DRY cycle? If you have a gas dryer, is the gas turned on? Is your LPG bottle empty? Try drying similar weight clothes together. If the problem persists call for service. Pressing START/PAUSE does not start the dryer Is the lid open? Shut the lid and press START/PAUSE. Is there a fault displayed on the display screen? Refer to page 57, – Before you call for service. Dryer is taking a long time to dry Is the lint bucket full? If so empty it to improve performance. Is the airflow system free from obstruction? If you have a gas dryer, is the gas turned on? Is your LPG bottle empty? Has the dryer been vented correctly? Is the venting distance too great? Is the machine over-loaded? Have heavyweight items been separated from lightweight items? Are the clothes very wet when they are removed from the washing machine? Increase your washer’s spin speed. Are you using the AIR DRY cycle? Dryer keeps stopping and starting Your dryer has a reverse action tumble. When it changes direction it will pause momentarily and will start again in the opposite direction, this is normal. Has WRINKLE FREE been selected? Solving drying problems 59 Linting Problems Is the lint bucket full? When lint reaches the top of the transparent section of the bucket it needs emptying. Have you separated lint-shedding garments (eg towels) from lint receiving garments (eg synthetics). Have you checked your pockets for tissues or other items that could have been left in them? Have you over-loaded your dryer? Over-loading can result in linting problems due to reduced airflow and lint not being able to collect on the filter. Have you over-dried your load? Over-drying can cause lint-attracting static electricity. Try a EN lower Dryness Setting or use AUTO-SENSING instead of TIME DRY. Is the lint bucket in place? Static problems Have your clothes been over-dried? Choose a lower dryness setting. Have you used fabric softener? Place fabric softener sheets in the dryer. Items shrinking Has the load been over-dried? Choose a lower dryness setting. Is tumble-drying recommended? Check care labels inside garments. If you selected TIME DRY - did you set it to dry for too long? Has the correct temperature been used to dry the garment? Check the care label. Clothes are wrinkled Does the load sit hig...
Questo manuale è adatto anche per i modelli :essiccatori - AeroSmart DG62T27C (1.54 mb)