valutazioni - , GPA: ( )

Istruzioni per l'uso Hobart Welding Products, Modello AIRFORCE 700I

Produttore : Hobart Welding Products
File Size : 1.38 mb
File Nome : 435edd1c-f50d-4f93-8d66-bbab3d5c6b0d.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

(362 mm) 4-3. Power Source Dimensions And Weight loc_2 3/96 - Ref. 244 405-A 8-1/4 in. (210 mm) 11-1/4 in. (286 mm) Dimensions And Weight 31.4 lb (14.2 kg) including torch 4-4. Torch Dimensions And Weight 3.0 lb (1.4 kg) Ref. 801 397-A 1 in. (25 mm) 8-3/8 in. (213 mm) 1-3/8 in. (35 mm) A complete Parts List is available at OM-244 013 Page 13 4-5. Selecting A Location loc_2 3/96 - Ref. 244 405-A ! Do not move or operate unit where it could tip. 18 in. (460 mm) 18 in. (460 mm) ! Special installation may be required where gasoline or volatile liquids are present see NEC Article 511 or CEC Section 20. 4-6. Connecting Gas/Air Supply Ref. 244 423-A Use only clean, dry air with 90 to 120 psi (621 to 827 kPa) pressure. 1 Gas/Air Inlet Opening 2 Hose 3 Teflon Tape Obtain hose with 1/4 NPT righthand thread fitting. Wrap threads with teflon tape (optional) or apply pipe sealant, and install fitting in opening. Route hose to gas/air supply. Tools Needed: 3 From Gas/Air Supply 1 2 9/16 in. 4-7. Connecting Work Clamp Do not connect work clamp to the portion of the workpiece that will fall when cut. 1 Work Clamp 2 Workpiece Connect work clamp to a clean, paint-free location on workpiece, as close to cutting area as possible. 1 2 Ref 803 915-A . A complete Parts List is available at 4-8. Electrical Service Guide Failure to follow these electrical service guide recommendations could create an electric shock or fire hazard. These recommendations are for a dedicated branch circuit sized for the rated output and duty cycle of the welding power source. NOTICE . INCORRECT INPUT POWER can damage this welding power source. This welding power source requires a CONTINUOUS supply of input power at rated frequency10%) and voltage 10%). Phase to ground voltage shall not exceed +10% of rated input voltage. Do not use a generator with automatic idle device (that idles engine when no load is sensed) to supply input power to this welding power source. 60 Hz Single Phase Input Voltage (V) 208 230 Input Amperes (A) At Rated Output 33 30 Max Recommended Standard Fuse Rating In Amperes 1 Time-Delay Fuses 2 Normal Operating Fuses 3 40 50 35 45 Min Input Conductor Size In AWG 4 3 10 Max Recommended Input Conductor Length In Feet (Meters) 80 (24) 98 (30) Min Grounding Conductor Size In AWG 4 10 10 Reference: 2008 National Electrical Code (NEC) (including article 630) 1 If a circuit breaker is used in place of a fuse, choose a circuit breaker with time-current curves comparable to the recommended fuse. 2 “Time-Delay” fuses are UL class “RK5” . See UL 248. 3 “Normal Operating” (general purpose -no intentional delay) fuses are UL class “K5” (up to and including 60 amps), and UL class “H” ( 65 amps and above). 4 Conductor data in this section specifies conductor size (excluding flexible cord or cable) between the panelboard and the equipment per NEC Table 310.16. If a flexible cord or cable is used, minimum conductor size may increase. See NEC Table 400.5(A) for flexible cord and cable requirements. 4-9. Extension Cord Data . When calculating max. cord length, remember to include conductor length from line disconnect device to input power receptacle. Input Voltage Input Power Phase Hertz Fuse Size Or Circuit Breaker Rating Conductor Size Max. Cord Length 208 V 1 60 Time-Delay 2 40 A Normal Operating 3 50 A 10 AWG 80 ft (24 m) 230 V 1 60 Time-Delay 2 35 A Normal Operating 3 45 A 10 AWG 98 ft (30 m) 2 “Time-Delay” fuses are UL class “RK5” . 3 “Normal Operating” (general purpose . no intentional delay) fuses are UL class “K5” (up to and including 60 amp), and UL class “H” ( 65 amp and above). OM-244 013 Page 14 . A complete Parts List is available at 4-10. Serial Number And Rating Label Location The serial number and rating information for this product is located on the back. Use rating label to determine input power requirements and/or rated output. For future reference, write serial number in space provided on back cover of this manual. 4-11. Connecting 1-Phase Input Power For 240 VAC 803 766-B / Ref. 802 443-A Installation must meet all National and Local Codes have only qualified persons make this installation. Disconnect and lockout/tagout input power before connecting input conductors from unit. Always connect green or green/ yellow conductor to supply grounding terminal first, and never to a line terminal. 1 Black And White Input Conductor (L1 And L2) 2 Green Or Green/Yellow Grounding Conductor 3 Input Power Cord. 4 Disconnect Device (switch shown in the OFF position) 5 Disconnect Device Grounding Terminal 6 Disconnect Device Line Terminals Connect green or green/yellow grounding conductor to disconnect device grounding terminal first. Connect input conductors L1 and L2 to disconnect device line terminals. 7 Over-Current Protection Select type and size of over-current protection using Section 4-8 (fused disconnect switch shown). 8 Receptacle (NEMA 6-50R) Customer Supplied Close and se...