valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
3. Verify that all power is switched on. 4. If the projector still does not produce an image, re-start the computer. 5. If the image sill does not appear, unplug the projector from the computer and check the computermonitor’s display. The problem may be with your graphics controller rather than with the projector. (Whenyou reconnect the projector, remember to turn the computer and monitor off before you power up the projector. Power the equipment back on in order of: Projector and computer.) 6. If the problem still exists, check the following chart. Try these Solutions No Power • Plug the projector into the AC outlet. • Be sure READY Indicator light is On. • Wait 90 seconds after the projector is turned OFF before turning the projectorback on. NOTE : After pressing the power ON-OFF switch to OFF, make sure theprojector works as follows: 1. The LAMP indicator will light and the READY indicator will turn off. 2. After 90 seconds, the READY indicator will light green again and the projector may be turned on by pressing the power ON-OFF button. • Check WARNING TEMP. indicator. If the indicator flashes red, the projector cannot be turned on. (See “TURNING ON/OFF THE PROJECTOR” section on page 20.) • Check the Projection Lamp. (Refer to page 40.) Image is out of focus • Adjust the focus • Make sure the projection screen is at least 4.6’ (1 .4m) from the projector. • Check the projection lens to see if it needs cleaning. NOTE : Moving the projector from a cool temperature location to a warm temperature location may result in moisture condensation on the lens. In suchan event, leave the projector OFF and wait until condensation disappears. Picture is Left/Right reversed • Check Ceiling / Rear feature. (See “SETTING” section on page 36.) Picture is Top/Bottom reversed. • Check Ceiling feature. (See “SETTING” section on page 36.) Some displays are notseen during the Operation. • Check Display feature. (See “SETTING” section on page 36.) No image • Check the connection between the computer or video equipment and the projector. • When turning the projector on, it takes about 30 seconds to display the image. • Check the system that you select is corresponding with the computer or the video equipment. • Make sure the temperature is not out of the Operating Temperature (5°C 35°C). No sound. • Check audio cable connection from audio input source. • Adjust the audio source. • Press VOLUME (+) button. • Press MUTE button. LC-XC1 Try these Solution Remote Control Unit does not work Check the batteries. Check the ALL-OFF switch on the Remote Control Unit is set to “ON.”. Make sure nothing is between the Remote Receiver and the RemoteControl Unit. Make sure you are not too far from the projector when using theRemote Control Unit. Maximum operating range is 16.4’ (5m). Make sure the code of the Remote Control is set to conform to the projector. (See “SETTING” section on page 36, 37.) Wireless Mouse function does not work. • Check the cable connection between the projector and the computer. • Check the mouse setting on your computer. • Turn the projector on before you turn on the computer. WARNING: High voltages are used to operate this projector. Do not attempt to open the cabinet. If the problem still persists after following all operating instructions, contact the sales dealer where you purchased the projector or the service center. Give the model number and explain the difficulty. Wewill advise you how to obtain service. This symbol on the nameplate means the product is Listed by UnderwritersLaboratories Inc. It is designed and manufactured to meet rigid U.L. safetystandards against risk of fire, casualty and electrical hazards. Projector Type Multi-media Projector Dimensions (W x H x D) 12.44” x 6.46” x 18.9” (31 6mm x 164mm x 480mm) Net Weight 20.3 lbs (9.2 kg) LCD Panel System 1 3” TFT Active Matrix type, 3 panels Panel Resolution 1024 x 768 dots Number of Pixels 2,359,296 (1024 x 768 x 3 panels) Color System PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N High Definition TVSignal 480i, 480p, 575i, 575p, 720p, i035i, 1080i-50 and iO8Oi-60 Scanning Frequency H-sync. 15 100 KHz, V-sync. 50 100 Hz Projection Image size (Diagonal) Adjustable_from_31” to 400” Horizontal Resolution 800 TV lines Projection Lens F 1.8 2.1 lens with f 48.4 mm 62.8 mm with motor zoom, focus and shift Throw Distance 4.6’ 47.2’ (1.4 m 14.4 m) Projection Lamp 250 W AV Input Jacks RCA Type x 3 (Video/Y, Pb/Cb, Pr/Cr) and Mini DIN 4 pin x 1 (S-Video) AV Audio Input Jacks RCA Type x 2 Computer Input Jacks (VGA) HDB 15 Terminal x 1, DVI 24 pin x 1, and BNC jack x 5 Computer Audio InputJacks Mini Jack (stereo) x 2 Control Port Jacks Mini DIN 8 pin x 2 Monitor Output Jacks BNC jack x 5 (Computer) and RCA Type x 1 (Video) Audio Output Jacks RCA Type x 2 Internal Audio Amp 2.0 W RMS (stereo) Built-in Speakers 2 speakers, 1.57” x 2,76” (40mm x 70mm) Feet Adjustment 0o to 9.0o Voltage and Power Consumption AC 100 120 V (4.4 A Max. Ampere), 50 / 60 Hz (The U.S.A and ...
Questo manuale è adatto anche per i modelli :TV - LC-XC1 (1.55 mb)