valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
Genuine Humminbird® accessories offer the opportunity to upgrade and expand the capabilities of your Humminbird® product. Your Humminbird® accessory is designed for trouble-free use in even the harshest marine environment. In the unlikely event that your Humminbird® accessory does require repairs, we offer an exclusive Service Policy -free of charge during the first year after purchase, and available at a reasonable rate after the one-year period. For complete details, see the Warranty section included in this manual. Contact our Customer Resource Center at 1-800-633-1468 or visit our website at Installation Overview Following are instructions for the installation of this accessory. Before you start installation, we encourage you to read these instructions carefully in order to get the full benefit from your Humminbird® accessory. If you find that any items are missing from your installation kit, call our Customer Resource Center at 1-800-633-1468 or visit our website at To install your Quick Disconnect mounting system, you will need a drill, your control head, the mounting bracket, the connector holder, the power cable, the mounting hardware, a 9/64" drill bit, a 1" hole saw, a Phillips and a flat-head screw driver, an adjustable wrench, a level, and marine-grade silicone sealant. Installation Perform the procedures in the following sections to install the Wide Quick Disconnect mounting system on your boat. 1.Determine Where to Mount Begin the installation by determining where to mount the control head. Consider the following to determine the best location: • To check the location planned for the control head, test run the cables for power, transducer and Temp/Speed accessory (if applicable). • There are two ways to route the cables to the unit: through a hole in the mounting surface underneath the mounting bracket, or from a hole outside the mounting bracket. Routing the cables under the mounting bracket provides maximum weather protection; this may not be feasible, however, if the area under the control head is inaccessible. In this case, route the cables through a hole at another location and cover with the supplied hole cover. • The mounting surface should be stable enough to protect the control head from excessive wave shock and vibration, and should provide visibility while in operation. • The mounting area should allow sufficient room for the unit to pivot and swivel freely, and for easy removal and installation (see illustrations). 530516-1_D 360 Degree Swivel 90 Degree Tilt © 2008 Humminbird®, Eufaula AL, USA. All rights reserved. Quick Disconnect Mounting Bracket 2.Drilling the Mounting Holes 1. Set the mounting bracket in place on the mounting surface. Mark the four mounting screw locations with a pencil or a punch. 2. Set the mounting bracket aside, and drill the four mounting holes using a 9/64” drill bit. If you have access to the underside of the mounting surface, mark and drill a 1” hole centered between the four mounting screw holes. Drilling the Mounting Holes 1"(25mm)HoleLocation Mounting Mounting Hole Hole Locations Locations 3.Route the Cables Through the Mounting Bracket 1a. If the cables must pass through a hole directly beneath the mounting bracket, mark and drill an additional 1" (25 mm) hole centered between the four mounting holes. Route the cables through the grommet, then press the grommet in place around the cables and into the 1"(25 mm) hole. Pass the cables out of the top of the mounting bracket. 1b. If the cables cannot be routed directly beneath the mounting bracket, mark and drill a 1" (25 mm) hole that will allow you to run the cables close to the bracket. Pass the cables through the 1" (25 mm) hole, through the mounting base, and out of the top of the mounting bracket. Using needle-nose pliers, break out the tabs on the rear of the mounting base. Place the Hole Cover over the mounting surface hole, then use it to mark the position of the two mounting screws. Remove the Hole Cover, drill the two mounting holes using a 9/64" (3.5 mm) bit, fill them with marine-grade silicone, then replace the Hole Cover and insert the #8 Phillips countersink wood screws. Hand-tighten only. NOTE: Remove the break-out tables only if the cable hole is not under the mount. 2. Place the mounting bracket on the mounting surface aligned with the drilled holes and fill the mounting holes with marine grade silicone. Insert the four #8 Phillips countersink wood screws into the mounting holes. Hand-tighten only. CAUTION! Do not cut or shorten the transducer cable, and try not to damage the cable insulation. Route the cable as far as possible from any VHF radio antenna cables or tachometer cables to reduce the possibility of interference. If the cable is too short, extension cables are available to extend the transducer cable up to a total of 50'. For assistance, contact the Customer Resource Center at or call 1-800-633-1468 for more informat...