valutazioni - 5, GPA: 4.8
(
)
)
|
Facilità d'uso
INSTALLATION Installing Batteries in the Remote Control 1 Slide the back cover all the way out to open the battery compartment of the remote control. Ў Make sure to match the “+” and 2 “–” ends of the batteries with the Install two AAA size diagram inside the compartment. batteries. Ў Remove the batteries and store 3 them in a cool, dry place if you won’t Replace the cover. be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV. (Assuming typical TV usage, the Batteries last for about one year.) 2.9 CHAPTER TWO: INSTALLATION Chapter Three OPERATION Turning the TV On and Off Press the Power button. You can also use the POWER button on the front panel. Plug & Play Feature When the TV is initially powered On, five basic customer settings proceed automatically and subsequently: Setting the language, Setting the Clock, Setting the Antenna, Ant. input check, and Auto program. 1 Press the Power button on the remote control. The message “Plug & Play” is displayed. It flickers for a little while and then the “Language” menu is automatically displayed. 2 Move the joystick to the right or left to select the desired language. Press Menu to enter the language, and then the “Clock Set” menu is automatically displayed. 3 Move the joystick down to select “Clock”. Set the hour or minute by moving joystick (refer to “Setting the clock” on page 3.19.) Press Menu to enter the setting the clock, and then the “Antenna” menu is automatically displayed. continued... CHAPTER THREE: TV OPERATION 3.1 OPERATION 4 Move the joystick left or right to select "A" or “B”. Press the Menu button to enter the Antenna Setting, and then “Ant. Input Check” is automatically displayed. 5 Make sure that the antenna is connected to the TV. Then move the joystick left or right to activate "Auto Program" or press Menu to skip. (refer to “Auto program” on page 3.9.) 6 When you have finished, press the Menu button. The message “Enjoy your watching..” is displayed. 7 If you want to reset this feature (1)Press the Menu button. (2) Move the joystick down to select the “FUNCTION” menu and press the joystick to enter. (3) Move the joystick down to select “Plug & Play” and press the joystick to enter. The message “Plug & Play” is displayed. Note: Plug & Play feature doesn’t work when the V-chip is on or when in the A/V mode. 3.2 CHAPTER THREE: TV OPERATION OPERATION Using the Perfect Focus Feature (HCL652W/HCL6515W/HCL4715W/HCL473W/HCM5525W/ HCM553W/HCM6525W/HCM653W) When the picture size is distorted after moving the TV set, use the Perfect Focus feature to adjust for the optimum picture size set in the Factory. Press the Menu button . Move the joystick down to select “FUNCTION”, then press the joystick to enter. 2 Move the joystick down to select “Convergence”, then press the joystick to enter. 3 Move the joystick down to select “Perfect Focus”, then press the joystick to enter. Perform Perfect Focus in the following sequence: green . red . Blue. The Perfect Focus feature ends after the cursor flickers for one second. Press Menu button to exit. Notes • If any error happens during Perfect Focus, then perform Perfect Focus once again. • If you can’t make adjustments after Perfect Focus, then make manual adjustments. Still you can’t make adjustments, contact your Service Center. • The Perfect Focus function doesn’t operate when component input is in 480P. CHAPTER THREE: TV OPERATION 3.3 OPERATION Adjusting Manual Convergence If the color appears spread out or “smeared” on the screen, the convergence probably needs alignment. Be sure to use the remote control for the convergence adjustments. First steps: 1 Press the Menu button. Move the joystick down to select “FUNCTION”, then press the joystick to enter. 2 Move the joystick down to select “Convergence”, then press the joystick to enter. 3 The “Manual Convergence” screen will appear, and the word “Red” will be highlighted. continued... 3.4 CHAPTER THREE: TV OPERATION OPERATION Adjust Red Convergence While “Red” is highlighted, press the joystick to enter: A crosshair pattern will appear on the screen. Move the joystick up/down/left/right to select where to adjust Convergence. 5 If a horizontal red line is visible, use CH and CH buttons to move the line so that it is superimposed on the horizontal center-line (i.e., make a single horizontal line that is as white as possible.) 6 If a vertical red line is visible, use the VOL + and VOL -buttons to move the line so that it is superimposed on the vertical-center line (i.e., make a single vertical line that is as white as possible.) 7 For ‘Blue’ adjustment, do the same as the above. After the red convergence is correctly adjusted, press Menu to exit all the menus. Note: Since the center convergence adjustments can’t be done after completing the side convergence adjustments, do the center convergence adjustments first. If you have done the side convergence adjustments first, then end the Convergence Adjustments by p...
Questo manuale è adatto anche per i modelli :TV - HCM5525W (3.84 mb)
TV - HCL5515W (3.84 mb)
TV - HCL 6515W (3.84 mb)
TV - HCL 473W (3.84 mb)