valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Helpful Hints CCZ130comb 4/5/99 7:31 PM Page 6 6 Hooking Up The TV/VCR 1 Hook up your TV/VCR using one of the connections shown. A. Connect a Cable signal or an antenna to the ANT(enna) Jack. Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna ANT. ANT. B. Hooking Up Your TV/VCR With a Cable Box To view any channel, set the TV/VCR to the Cable Box output channel (channel 03 or 04). Then, select channels at the Cable Box. Connect the Cable signal to the IN Jack on the Cable Box. Connect an RF coaxial cable (75ohm, not supplied) to the OUT Jack on the Cable Box and to the ANT(enna) Jack on the TV/VCR. ANT. ANT. INOUT C. Hooking Up Your TV/VCR With an Indoor Antenna To install a rod antenna (not supplied), push the stem of the antenna into the antenna hole on the top of the TV/VCR. Connect the antenna wire to the ANT(enna) Jack on the back of the TV/VCR as shown. Extend the antenna and adjust its length, direction, and angle for the clearest picture. Rod Antenna (not supplied) ANT. ANT. CCZ130comb 4/5/99 7:32 PM Page 7 Hooking Up The TV/VCR (cont’d) 7 D. Hooking Up Your TV/VCR to Another Video Source (VCR or Camcorder) You may need this connection if you want to copy tapes. Details are on page 31. Use an Audio cable to connect the AUDIO EARPHONE AUDIO VIDEO STOP/EJECT REW PLAY F.FWD REC/OTR CHANNEL VOLUME POWER OUT IN VIDEO IN OUT 3CH 4CH AUDIO ANT. OUT IN VIDEO IN OUT 3CH 4CH AUDIO ANT. VIDEOAUDIO AUDIO/VIDEO Jacks on front of TV/VCR AUDIO/VIDEO OUT Jacks on VCR OUT Jack on the VCR to the AUDIO Jack on the front of the TV/VCR. Use a Video cable to connect the VIDEO OUT Jack on the VCR to the VIDEO Jack on the front of the TV/VCR. 2 Plug in the TV/VCR. 3 Before you turn on the TV/VCR, go to page eight. Helpful Hints • Before connecting an antenna or cable signal to the ANT(enna) Jack, make sure the pin is not bent. If the pin is bent, straighten it as illustrated, then connect the antenna or cable signal to the ANT(enna) Jack. • A rod antenna (not supplied) is available from Philips Service Solutions Group. The part number is 4835 303 37006. To order, call 1-800-851-8885. • Audio and video cables are not supplied. Crooked Pin Straight Pin Bent pin PlugCable CCZ130comb 4/5/99 7:32 PM Page 8 8 Turning On the TV/VCR Before you turn on the TV/VCR, make sure there are batteries in the remote control and the TV/VCR is hooked up correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. 1 Press the POWER button. The TV/VCR will come on and the screen shown below will appear. SELECT LANGUAGE > ENGLISH ON ESPANOL SELECT KL OR PRESS MENU TO CONTINUE 2 Press the PLAY/K button or the STOP/L button to select English or Spanish on-screen displays. 3 Press the MENU button. The screen shown below will appear. CONNECT ANTENNA OR CABLE TO TVCR THEN PRESS B TO END PRESS EXIT POWER CLEARSTATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP MUTE SPEEDVOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILLSTOP/ +100 ALT.CH MENU MEMORY1 2 3 4 5 4 Press the FF/SEARCH B button to begin automatic channel setup. The TV/VCR will memorize all available channels. When channels are set, CHANNELS ARE SET will appear on- screen briefly. Then the TV/VCR will go to the lowest channel programmed. (If you try to set up channels when there is no antenna or cable connected to the TV/VCR, programming will appear to take place, but eventually a NO TV SIGNALS ... message will appear on- screen. Connect an antenna or cable to the TV/VCR, then try again. You may need to follow the steps on page 10 instead.) 5 Use the CHANNEL o/p buttons or the Number buttons on the remote control to select a TV/VCR channel. Use the VOLUME o/p buttons to adjust the sound. Helpful Hints • If you do not see any on-screen displays when you turn on the TV/VCR, check your hookups, then try again. If you still do not see any on-screen displays, follow the steps on pages nine - 10 to select a language and set up channels. • To skip step 2, press the MENU button. All on-screen displays will be in English. To skip step 4, press the STATUS/EXIT button. Channels will not be set up, and CHANNELS NOT SET will appear on-screen briefly. • You cannot set up channels if you are using a Cable Box. • Line Input mode will always be stored in the TV/VCR’s memory as channel 00. When you select channel 00, A/V IN will appear on- screen briefly. Press the CHANNEL o/p buttons or Number buttons to select another channel. CCZ130comb 4/5/99 7:32 PM Page 9 Language Selection 9 Follow the steps below to change the language of the on-screen displays. 1 Press the MENU button. Press the PLAY/s PRIMARY SETUP > SELECT LANGUAGE AUTO PROGRAMMING CH MEMORY REVIEW VOLUME BAR [ON] SET CLOCK SELECT KL CHOOSE B TO END PRESS EXIT > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 1 PRIM. SETUP. Then, press the FF/SEARCH B button. 2-4 POWER CLEARSTATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP MUTE SPEEDVOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILLS...
Questo manuale è adatto anche per i modelli :VCR / lettori video - CCZ130AT99 (611.06 kb)
VCR / lettori video - CCZ130AT (611.06 kb)