valutazioni - , GPA:
(
)
)
Produttore : DCS
File Size : 2.24 mb
File Nome : afa770fd-ff31-442f-8be3-0a2446e345dd.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
If DCS Mount products are used for purposes other than their original intent. DCS Mount, its distributors and retailers shall not be held responsible or liable for injuries or property damage, direct indirect, or consequential, which may arise from the inability to use this product safely, properly, and in the manner for which it has been designed and manufactured. Warranty does not apply to products, which have been lost, damaged by misuse, abuse, or accident. Thank you for choosing DCS Mount Fly your Flat Panel TV Illustration for hardware kit LP-80 Flat Panel Cantilever Mount Installation Instructions ..• 80 lb. Maximum weight capacity ..• VESA 75/100 compliant ..• Cantilever arm mount for large LCD and small plasma panels ..• Allows maximum flexibility for installing and viewing displays. ..• Cantilever arm provides full extension and 180..of lateral rotation for viewing from multiple locations. ..• Nesting arm design allows display to be folded parallel to wall ..• Provides full tilt and swivel capabilities for optimum viewing ..• Durable grey or black powder coat finish ..• Single stud mounting Check the Hare Ware Kit after open the package Description Quantity 3/16 inch Hex Wrench 1 5/32 inch Hex Wrench 1 7/32 inch Hex Wrench 1 5/16 x 3-1/2 inch Lag bolt 2 Philips Screw M5 x 8 mm 4 Philips Screw M5 x 12 mm 4 Philips Screw M4 x 8 mm 4 Philips Screw M4 x 12 mm 4 5/16 Washer 4 Button Head Screw 1/2-20 x 1/2 4 Read through the entire instruction manual before beginning. This flat panel cantilever will hold larger LCD monitor 30 inches and over. It will also hold smaller plasma monitors up to 32 inches. First determine if your monitor is VESA standard compliant, refer to the monitor’s users manual. VESA is a standard mounting hole pattern (see image 1). The LP-80 Flat Panel Cantilever can attach directly to both 75mm & 100mm VESA square hole patterns. If your monitor is not VESA standard compliant, a mounting adapter bracket will be needed between your monitor and the cantilever mount. Contact your dealer or contact DCS Mount to find out if an adapter is available for your monitor. All plasma will require an adapter bracket. You will need someone to help with this installation. 1. Determine your preferred mounting location keeping in mind good viewing angles and that this mount MUST BE PROPERLY SECURED TO THE CENTER OF A STUD. 2. While holding the mount in place and being sure that the mount is plumb, mark the mounting location (you can use the supplied lag bolts to poke marks into the mounting surface through the center of each mounting hole on the wall mounting plate). When mounting to a wood stud, drill a 3-1/4 inch deep pilot hole with a 9/32”drill bit through each mark. Attach the cantilever mount to the wall before attaching your monitor to the cantilever’s monitor mounting plate. 3. If your monitor has a table stand attached, you will need to remove the stand before attaching it to the cantilever mount; refer to the monitor’s users manual for proper instruction to remove the stand. In the hardware kit, there are 4 sets of screws with 4 screws per set supplied. Depending on your monitor’s manufacture’s specifications, determine the proper diameter & length of screws that you will need. CAUTION: Damage to your monitor’s internal components can occur if you use screws that are too long. Attach your monitor to the VESA plate using the proper screws, DO NOT over tighten the screws that attache to the monitor, DAMAGE to the monitor may occur. If your monitor needs an adapter bracket, use the supplied 1/4-20 screws to attache the bracket, once it has been mounted to your monitor, to the 100mm pattern on the VESA plate. 4. If you attach any wires along the cantilever’s swing arms (for example using P-CLIPS), be sure that the wires (or P-clips) are not pulled, pinched or kinked between the swing arms when you move the cantilever mount around into different positions. 5. All of the screws are properly torqued to specification when the unit is assembled at the factory and should not need an further initial adjustments. However, due to the variety in size of different monitors, MINOR adjustment may be required to optimize the tension needed for ease of movement. Be sure that your monitor is supported properly while making ANY changes to the cantilever. To loosen or tighten the 4 screws respectfully on the back of the rear pivot clamp until the desired tension is obtained (see image 2 – Tilt Tensioning Screws and Image 3 – Tensioning Tilt). It is important to try to maintain even torque on each of the 4 screws. It does not take that much change in torque to make a large difference in the tilt tension. To loosen or tighten the swing arm tension use the supplied 5/32 inch hex wrench to loosen or tighten the screw shown in image 2 & 3 (Swing Arm Tensioning Screw). Periodic adjustment of these screws may be necessary to maintain desired tension. There should be NO reason to tighten or loosen the wrist hinge bracket...