Do not force the clip. The clip will slide into place. This completes the Diamond Shield installation. The Diamond Shield protects the actual television (lenticular) screen, however it can be removed to reduce glare or background reflections. Removal: To remove the Diamond Shield, reverse the order of the above procedure. WARNING Sharp edges! Always wear gloves to handle, lift and install the Diamond Shield and molding clips. Sharp objects (such as tools, hand jewelry and fingernails) may scratch or damage the Diamond Shield. Use caution when removing or installing. Mitsubishi recommends using a flat, plastic card (such as a credit card) to remove the molding clips. Store the Diamond Shield in a safe place to prevent damage. Damage caused to the TV by non-authorized changes or actions are not covered under warranty. The Limited Warranty does not cover damage resulting from improper installation or removal of the Diamond Shield. I IMPORTANT I The Diamond Shield on the WT-42315 is not designed to be removed by the customer. 69 Appendix E: Diamond Shield™ Installation and Removal for WS-48315, WS-55315, WS-65315 and WS-65315A Cabinet Separation for Model WS-65315 and WS-65315A Cabinet Separation for WS-65315 and WS-65315A This TV is very heavy! Exercise extreme care when moving TV as foreign material may become embedded in the castor wheels which could damage wood or other delicate flooring._ For Mitsubishi Dealers and Service Personnel ONLY This Mitsubishi projection television cabinet has been assembled in two pieces. These pieces may be separated to allow for easier delivery and setup. The instructions below show how to safely separate and reattach the cabinet. IMPORTANT This projection television weighs over 320 pounds and has many sensitive components. Any dismantling procedure should be done by authorized Mitsubishi Dealers or Service Personnel ONLY. The following operations should be performed by two people: 1 .Remove the decorative Plastic covers (2) on each side of the cabinet and then remove the exposed screws (2) on each side. О ° V ° >^4 Plastic covers, screws 0 Speaker grille шяня Connector (ZF) 2. Remove the Speaker grille by pulling it straight off the cabinet. 3.Disconnect the connector (ZF). 4. Carefully lift the Cabinet-Top straight up until the brackets are clear from the Cabinet-Bottom. DO NOT use the Screen Frame Bottom when lifting the Cabinet-Top. 5. Carefully place the Cabinet-Top on to the floor. 6. After moving and positioning the Cabinet-Bottom in its desired location, reverse the procedure and mount the Cabinet-Top on the Cabinet-Bottom. Be sure you align the brackets properly. Keep fingers clear of all joints! Reconnect the connector, replace the speaker grille, screws and decorative plastic covers. Screen Frame 70 Terminal Cover Ventilation for Model WT-42315 Wall Stand Requirement CAUTION: This PTV for use only with Mitsubishi stand MB-42413. Use with other stands may result in instability causing possible injury. Air Circulation Tip When considering the location or position of your TV, we recommend you place it at least 2” (inches) away from the wall. Like most electrical equipment and appliances, better air circulation allows your television to run cooler, assuring a long, trouble-free life. At Least 2” (Inches) Away from Wall Side Panel for Input Terminal Included in the accessories bag is the side panel to cover the input terminals, located on the bottom right of your TV. See diagram. Follow the steps below to attach or remove this side panel: 1. Remove the side panel from the accessories plastic bag attached to the back of your TV. 2. Route all of the cable downward so the cover can close over them. 3. Position the three tabs directly opposite the three slots (see diagram) and gently push toward the front of the TV. 4. Slide the two push tabs into the slots on the other side of the terminals until both tabs snap into place. Result: The side panel neatly covers the input jacks. Reverse these steps to remove the side panel from the input terminal. Slots for Push Tabs Side Panel Slots 71 Terminal Cover Ventilation for Model WT-42315 Index Index A A/V Memory Reset 55 Receiver, Connecting 17 Activating the PIP and POP 29 Advanced Convergence Menu 53 Advanced Features Menu 34, 50-54 Antenna Channel Edit Menu 42 Connecting 14, 15 Appendices A: Bypassing the V-Chip Lock 63 B: High Definition Input Connection Compatibility 65 C: Remote Control Programming Codes 66 D: Cleaning and Service 68 E: Diamond Shield™ Installation and Removal for Models WS-48315, WS-55315, WS-65315, WS-65315A 69 Audio/Video Settings Menu 34, 55 A/V Memory Reset 55 Audio Output 55 TV Speakers 55 Audio Settings Menu 55 Audio Settings Description 56 Automatic POP Switching 62 Auto Color Correction Menu 50 Available On-Screen Format Sizes 60 B Back Panel Input/Output for WS-48315, WS-55315, WS-65315, WS-65315A 11 Black Enhancement Menu 54 Bypass...

Questo manuale è adatto anche per i modelli :
TV - WS-48315 (3.78 mb)
TV - WS-48315 (3.78 mb)
TV - WS-55315 (3.78 mb)
TV - WS-48315 (3.78 mb)