valutazioni - 4, GPA: 4.5
(
)
)
|
Facilità d'uso
For best reception an outdoor antenna is recommended. • Connect home antenna to ANT connection on back of television. Note: Cable Mode is preset at the factory. Safety Precautions Incoming Cable from Home Antenna Please take safety precautions to prevent the unit from falling over. The unit may fall over during earthquakes, or if someone stands on or shakes the projection TV. Procedure • Use a strong rope or a chain (not included) to fasten the projection TV firmly to a strong support such as a wall or pillar. Viewing Position To optimize your viewing comfort, please follow the viewing guidelines shown in the diagrams below. If viewing for an extended period of time, sit as far back from the screen as possible. Viewing distance for 50” models is at least 6 feet and for 60” is at least 7 feet. 70o 70o 30o 30o Note: If you view the Projection Television at a short distance for a long time, your eyes may become fatigued. ENGLISH 5 • INSTALLATION ENGLISH Remote Control Battery Installation Requires two AA batteries (supplied). + + - + + - + - 1 2 3 Procedure 1. Remove battery cover by pushing in on the catch while lifting the cover up. 2. Install batteries by matching (+) and (-) polarity signs in the compartment. 3. Re-insert the cover and press down the cover until it snaps shut. Note: Incorrect installation can cause battery leakage and corrosion that will damage the Remote Control. Precautions • Replace batteries in pairs. • Do not mix battery types (zinc carbon with alkaline). • Do not recharge, heat, short-circuit, disassemble, or burn batteries. Replacing the lamp unit (For USA and Canada only) (USA only) The lamp unit is sold separately Lamp unit Part No. : TY-LA2004. To purchase a replacement, call the Panasonic accessory department, toll free at: 1-800-332-5368. (Canada only) For product operation and information assistance, please contact your Dealer or our Customer Care Centre at: (905) 624-5505. Lamp unit replacement period The lamp unit for the projection TV should be replaced after approximately 10,000 hours of use in the normal usage mode. Due to the characteristics and use conditions of individual lamps, the lamp may cease to light before the stated lamp life. Influences of frequent lighting, continuous light use for over 24 hours, the number of times lit, the length of time between lightings, etc. may shorten lamp life. Because of this, having a replacement lamp on hand is recommended. A warning will display after 10,000 hours of use. When the power is turned on after 10,000 hours of continued use, REPLACE LAMP will be displayed for approximately 1 min. A warning message to urge the replacement of the lamp will be displayed in red at the center of the screen. Important Points to keep in mind When replacing the lamp unit, pay attention to the following points. Warning: • The lamp unit is hot during operation and touching it immediately after use may cause burns. • Please allow the lamp to cool (for at least 1 hour) before handling or replacing the lamp unit. Cautions for Lamp Unit Replacement: • Handle the old lamp unit carefully. If mishandled, it may explode. • Wear gloves when replacing the lamp unit. • If replacing the lamp unit becomes necessary during the operation of the TV, follow the procedure below to turn off the power and wait until the lamp unit cools completely. Procedures to turn Power Off 1. Press the POWER button to turn off the power. 2. Wait for about one minute until the cooling fan stops. Note: The lamp cooling fan will continue to operate for about one minute after turning off the power. Do not unplug the power cord from the outlet until the fan has stopped. Avoid interrupting the power line such as by using circuit breakers or switchable power strips. 3. Unplug the power cord from the outlet. For USA and Canada only. Refer to the instructions enclosed with the lamp unit (Part No. TY-LA2004) when replacing the lamp. REPLACE LAMP 6 • POWER ON/OFF POWER ON/OFF Connecting the Plug to the Wall Outlet The projection TV must first be plugged into an AC outlet. The projection TV will then be in standby mode. Turning the Power ON and OFF Always be sure to follow the procedure below to turn the Projection Television power ON and OFF. The lamp cooling fan will continue to operate for approximately one minute after the power is turned off by the remote control. After the cooling fan has stopped, the power indicator will not illuminate (Stand-by mode). If you wish to turn the power ON while the cooling fan is operating, press the power button. The power indicator on the Projection Television will then flash in green, and the projection Projection Television will turn ON as soon as the cooling fan stops. Always use the remote control or power button on the Projection Television to turn the power OFF. Caution: Do not turn off by external power strip or by pulling plug. Do not open any circuit breakers while the cooling fan is still operating. Procedure for turning ON • Press the Power b...
Questo manuale è adatto anche per i modelli :TV - PT60DL54 (3.28 mb)
TV - PT50DL54 (3.28 mb)
TV - PT 50DL54 (3.28 mb)