If you use parts provided by another manufacturer, it may result in a problem with the product or fire due to an increase in the internal temperature of the product due to poor ventilation. The appearance may differ depending on the product. When installing the product with a stand When installing the product with a wall-mount O N ¦ ¦ N – – N 0 cm 0 cm 0 cm 0 cm 0 cm 0 cm 0 cm English - 25 English - 26 Securing the TV to the Wall Caution: Pulling, pushing, or climbing on the TV may cause the TV to fall. In particular, ensure your children do not hang over or destabilize the TV; doing so may cause the TV to tip over, causing serious injuries or death. Follow all safety precautions provided on the included Safety Flyer. For added stability, install the anti-fall device for safety purposes, as follows. To avoid the TV from falling: 1. Put the screws into the clamps and firmly fasten them onto the wall. Confirm that the screws have been firmly installed onto the wall. You may need additional material such as an anchor depending on the type of wall. Since the necessary clamps, screws, and string are not supplied, please purchase these additionally. 2. Remove the screws from the centre back of the TV, put the screws into the clamps, and then fasten the screws onto the TV again. Screws may not be supplied with the product. In this case, please purchase the screws of the following specifications. Screw Specifications For a 17 ~ 29 Inch LCD TV: M4 X L15 For a 32 ~ 40 Inch LCD TV: M6 X L15 3. Connect the clamps fixed onto the TV and the clamps fixed onto the wall with a strong string and then tie the string tightly. Install the TV near to the wall so that it does not fall backwards. It is safe to connect the string so that the clamps fixed on the wall are equal to or lower than the clamps fixed on the TV. Untie the string before moving the TV. 4. Verify all connections are properly secured. Periodically check connections for any sign of fatigue for failure. If you have any doubt about the security of your connections, contact a professional installer. ¦ . N N N N–– N N N Wall Wall ¦ Troubleshooting If you have any questions of TV, first refer to this list. If none of these troubleshooting tips apply, please visit ‘site, then click on Support or contact Call Centre on list of last page. Issue Solution Picture Quality First of all, please perform the Picture Test to confirm that your TV is properly displaying test image. Go to MENU -Support -Self Diagnosis -Picture Test If the test image is properly displayed, the poor picture may caused by the source or signal. . TV image does not look as good as it did in the store. Picture is distorted : macroblock, small block, dots, pixelization Wrong or missing colour with Component connection. Poor colour or brightness. . Compression of video contents may cause picture distortion especially on fast moving pictures such as sports and action movies. . Low signal level or bad quality can cause picture distortion. This is not a TV issue. . Make sure the Component cables are connected to the correct jacks. Incorrect or loose connections may cause colour problems or the screen will be blank. . Adjust Picture options in the TV menu. (Picture mode, Colour, Brightness, Sharpness) . Adjust Energy Saving option in Setup menu. . Try picture reset to view the default picture setting. (Go to MENU -Picture -Picture Reset) Dotted line on the edge of screen. If picture size is set to Screen Fit, change to 6:9. Change cable/set top box resolution. . . Picture is black and white with AV (Composite) input only. Connect video cable(Yellow) to Green jack of component input 1 of the TV. . Picture freezes or is distorted when changing channels or picture is delayed. If connected with cable box, please try to reset cable box. (reconnect AC cord and wait until cable box reboots. It may take up to 20 minutes.) Set output resolution of cable box to 1080i or 720p. . . Sound Quality First of all, please perform the Sound Test to confirm that your TV audio is properly operating. Go to MENU -Support -Self Diagnosis -Sound Test If the audio is OK, the sound problem may caused by the source or signal. . No sound or sound is too low at maximum volume. Please check the volume of external device connected to your TV then, adjust the TV volume accordingly. . Noise from speaker. Check cable connections. Make sure a video cable is not connected to an audio input. For Antenna/Cable connection, check signal strength. Low signal level may cause sound distortion. . . Picture is good but no sound. . If you have an analogue Cable/Set top box, upgrade to an Box. Use HDMI or Component cables to deliver HD picture quality. . Cable/Satellite subscriber : Try HD(High Definition) stations from channel line up. . Antenna connection: Try HD stations after performing Auto programme. N Many HD channels are upscaled from SD(Standard Definition) contents. . Adjust Cable/Set top box video output resolution to...
Questo manuale è adatto anche per i modelli : TV - LE19B650T6W (13.11 mb)
)
