valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
ASSY-HINGE (LEFT) 1 The wall mount bracket is delivered separately. Please tighten the captive screw in the direction of the arrow after assembling the bracket. Install the Wall Mount Bracket after the screws are securely inserted into the wall. Instructions on Securing the SET to the Wall Mount Bracket . The exterior of the SET may be different than the picture. (Assembly and installation of the plastic hanger is the same.) 1 Remove the screws from the back of the PDP. 2 Use the screw and assemble the plastic hanger. (Please refer to the following picture.) . 1 Please ask the installers to install the wall mount bracket. 2 Please be sure to check if the plastic hanger is completely secured on both the left and right side after hanging the SET on the wall mount bracket. 3 Please avoid catching your fingers while installing and adjusting the angle. 4 Please tightly secure the wall mount bracket to the wall to avoid injury from a falling SET. continued... English - 28 How to Install the Wall Mount Bracket 3 Tighten the screws of the plastic hanger (shown in picture 2) to the back side of the PDP. 4 Remove the Safety Pins. Fasten the 4 plastic latches assembled at step (#) on the back side of the PDP using the guide holes of the wall mount, push (!) and hook (@) down to secure the PDP on the wall mount as illustrated. Secure the PDP by inserting the Safety Pins, not to fall from the wall mount. PDP panel Wall attachment panel bracket Wall How to Adjust Mounting Angle . Please secure the mounting bracket on the wall surface after setting its angle at 0° 1 Secure the SET to the wall mount bracket.(Please refer to the follow ing instructions.) 2 Set the angle by pulling the upper end of the SET attached to bracket in the direction of the arrow. (Refer to the illustration on the right.) 3 The angle can be adjusted from 0° to 15° by ±2°. Hold onto the middle of the PDP to adjust the angle (not the sides of the PDP). Connecting External Devices to the PDP . To connect external devices such as a DVD or a Home Theater System to the PDP, please refer to following instructions: 1 Be sure to remove the safety pins underneath the PDP. . If the safety pins are not removed, the angle cannot be adjusted. Any attempt to do so may cause damage to the PDP. 2 Hold onto the bottom of the PDP and pull forward fully as directed by the arrow as illustrated) to adjust the angle. (0°~20° by 2°) Insert the Safety Pins to the front guide holes on both sides as illustrated in figure @. . Viewing the PDP after connecting the external devices Remove the Safety Pins to adjust the angle to 0°, and then secure the Safety Pins again. . For safety, be sure to secure the PDP using the safety pins. If the safety pins are not used, the PDP may fall, causing serious injury. Troubleshooting Before contacting the Samsung after-sales service, perform the following simple checks. If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local dealer. No sound or picture . Check that the mains lead has been connected to a wall socket. . Check that you have pressed the (Power) button (On/Off) on the front panel or press the POWER () button on the remote control. . Check the picture contrast and brightness settings. . Check the volume. . Check if Internal Mute is set to ON. Normal picture but no sound . Check the volume. . Check whether the volume MUTE button on the remote control has been pressed. No picture or black and white picture . Adjust the colour settings. . Check that the broadcast system selected is correct. Sound and picture interference . Try to identify the electrical appliance that is affecting the television, then move it further away. . Plug the television into a different mains socket. Blurred or snowy picture, distorted sound . Check the direction, location and connections of your aerial. This interference often occurs due to the use of an indoor aerial. Remote control malfunctions . Replace the remote control batteries. . Clean the upper edge of the remote control (transmission window). . Check that the “+” and “–” ends of the batteries are inserted correctly. . Check that the batteries are drained. Screen is black and power indicator light blinks steadily . On your computer check; Power, Signal Cable. . The TV is using its power management system. . Move the computer’s mouse or press any key on the keyboard. . On your equipment check (STB, DVD, etc) ; Power, Signal Cable. . The TV is using its power management system. . Press the Source button on the panel or remote control. . Turn the TV off and on. English - 29 This page is intentionally left blank. This page is intentionally left blank. Contact SAMSUNG WORLD-WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre. Country Customer Care Centre • Web Site AUSTRALIA 1300 362 603 CHINA 800-810-5858, 010- 6475 1880 www.samsung.com.cn...