valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
. [Brightness]: Change the intensity and details of the dark areas. . [Colour]: Change colour saturation. . [Sharpness]: Change sharpness. . [Noise reduction]: Filter and reduce noise. . [Tint]: Change the colour balance. . [Custom tint]: Customise tint setting. (Only available if [Tint] > [Custom] is selected) . [Digital Crystal Clear]: Control advanced settings to fine-tune each pixel to match surrounding pixels. Produce a brilliant, high definition image. - [Advance sharpness]: Enable superior sharpness, especially on lines and contours in the picture - [Dynamic contrast]: Set the level at which the TV automatically enhances details in the dark, middle and light areas of the picture. - [Dynamic backlight]: Reduce power consumption by dimming the TV backlight to match the room lighting conditions. - [MPEG artifact reduction]: Smooth the digital transitions in the picture. - [Colour enhancement]: Change the colours to be more vivid and improve the resolution of details in bright colours. - [Gamma]: Non-linear setting for picture luminance and contrast. . [PC mode]: When a PC is connected through HDMI, change the picture format to [Unscaled] to display maximum detail. . [Picture format]: Change the picture format. . [Screen edges]: Change the picture size. . [Picture shift]: Move the position of the picture. You cannot select this setting if the selected picture format is [4:3], [Auto fill], [Auto zoom] or [Wide screen]. More sound settings You can change the settings in the Sound menu. 1. Press . 2. Select [Setup] > [TV settings] > [Sound], then press OK. 3. Select a setting to change, then press OK: . [Smart sound]: Access predefined smart sound settings. . [Reset]: Reset to factory default settings. . [Clear sound]: Enhance the sound quality. . [Bass]: Change the bass level. . [Treble]: Change the treble level. . [Surround]: Switch on spatial sound. . [Custom colour]: Automatically reduce sudden volume changes, for example when switching channels. . [Headphone volume]: Change headphone volume. . [Balance]: Change the balance of the left and right speakers. . [Audio out delay]: Automatically sync the image on the TV to the audio from a connected home theatre. . [Audio out offset]: Change the setting for audio output delay. You cannot select this setting if [Audio out delay] is not switched on. . [Digital output format]: Select audio output through the digital audio connector. Select [PCM] to convert non-PCM audio or [Multichannel] to output to home theatre. . [Digital output level]: Set the sampling rate for PCM audio. [Normal] - No loss in intensity or signal strength; [Low] - Certain amount of loss in intensity or signal strength. Select audio format If a digital TV channel broadcaster streams audio in several formats, you can select an audio format. 1. Press . 2. Select [Setup] > [Channel settings] or [Satellite settings] > [Language]. 3. Select a setting, then press OK: . [Preferred audio format]: Receive standard audio format (MPEG) or advanced audio formats (AAC, EAC-3 or AC-3 if available). . [Mono/Stereo]: If stereo broadcasting is available, select mono or stereo audio. 4. Press to exit. Reset picture and sound You can restore the default picture and sound settings, while the channel installation settings remain the same. 1. While you watch TV, press . 2. Select [Setup] > [TV settings] > [Factory settings], then press OK. All TV settings (except for channel settings) are reset to the default factory settings. Channel settings Automatic install When the TV was switched on for the first time, a full installation of channels was performed. To change your language, country and reinstall all available TV channels, you can run this full installation again. Start installation 1. Press . 2. Select [Setup] > [Search for channels] > [Reinstall channels], then press OK. The Country menu is displayed. 3. Select your country, then press OK. 4. Select your network, then press OK: . [Antenna]: Access free-to-air antenna or digital DVB-T channels. . [Cable]: Access cable or digital DVB-C channels. 5. Follow the onscreen instructions to select other options, if any. The start menu for channel search is displayed. 6. Start channel search: . If your channel service provider instructs you to change settings, select [Settings], then press OK. Follow the service provider's instructions to complete the installation. . Otherwise, select [Start], then press OK. 7. Once the channel search is complete, select [Finish], then press OK. Tip: Press LIST to see the channel list. Note: When digital TV channels are found, the list of installed channels may display empty channel numbers. You can rename, reorder or uninstall these channels. Install analogue channels You can search and store analogue TV channels one by one. Step 1: Select your system Note: Skip this step if your system settings are correct. 1. While you watch TV, press . 2. Select [Setup] > [Channel settings] > [Channel installation]. 3. Select [Analogue: Manual ant...
Questo manuale è adatto anche per i modelli :TV - 42PFL3527K/02 (1.12 mb)