valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Cursor These 4 keys are used to move around the menus. Volume To adjust the sound level Mute To mute or restore the sound. Screen information To display / remove the programme number, the time, the sound mode and the time remaining on the timer. Hold down for 5 seconds to permanently display the programme number on the screen. 1 2 MENU ” P 5 64 87 9 0 3 + + . [ A . u SMART SMART RADIO E ¤ .Y Standby To set the TV to standby mode.To switch the TV set on again, press b,P @#or 09. Surround Sound To activate / deactivate the surround sound effect. For models equipped with Virtual Dolby Surround*, you can experience Dolby Surround Pro Logic sound effects. Sound mode Used to force programmes in Stereo and Nicam Stereo to Mono or, for bilingual programmes, to choose between Dual I or Dual II. The Mono indication is red when in forced position. 16:9 Format (p. 9) Smart picture and sound Used to access a series of predefined picture and sound settings. The personal position relates to settings selected from the menus. Teletext (p. 8) Selecting TV programmes To move up or down a programme. The number and the sound mode are displayed for a few seconds. For some TV programmes the title of the programme appears at the bottom of the screen. Numerical keys For direct access to programmes. For a 2 digit programme number, the 2nd digit must be entered before the dash disappears. Previous programme To access the previously viewed programme. * Manufactured under license from Dolby Laboratories.“Dolby” and the double-D symbols are trademarks of Dolby Laboratories. Connecting FM ANT. : FM ANT: • Insert the radio aerial lead supplied into the FM ANT socket located at the bottom of the TV. • Use the aerial connection lead supplied and connect the : socket situated at the bottom of the TV to your aerial socket. If you are using an indoor aerial, reception may be difficult in certain conditions.You can improve reception by rotating the aerial. If the reception remains poor, you will need to use an external aerial • Connect the power lead to the television and the mains plug into the wall socket (220-240 V/50 Hz). • Arrange the leads by passing them through the television stand. Connecting peripheral equipment Video recorder FM ANT: EXT1 VCR Other equipment EXT1 Video recorder (or DVD recorder) Carry out the connections shown opposite, using a good quality euroconnector cable. If your video recorder does not have a euroconnector socket, the only connection possible is via the aerial cable.You will therefore need to tune in your video recorder's test signal and assign it programme number 0 (refer to manual store, p. 6). To reproduce the video recorder picture, press 0. Video recorder with decoder Connect the decoder to the second euroconnector socket of the video recorder.You will then be able to record scrambled transmissions. Satellite receiver, decoder, DVD, games, etc. Make the connections as shown opposite. Side connections L R * Audio in Video in S-Video Make the connections as shown opposite.With the n key, select EXT2/S-VHS2. For a monophonic device, connect the audio signal to the AUDIO L input. The sound automatically comes out of the left and right speakers of the set. Headphones When headphones are connected, the sound on the TV set will be cut.The @ P # keys are used to adjust the volume level. The headphone impedance must be between 32 and 600 Ohms. Switching on When you turn on the TV set for the first time, a menu is displayed on screen.This menu prompts you to select the country and language for the menus: Plug’n’Play Country GB Language English w If the menu is not displayed, press and hold down the @ and # keys on the TV set for 5 seconds to display the menu. & Use the iI keys on the remote control to select your country and validate with ¬. If your countr y does not appear in the list, select choice “. . .” e Next select your language using the iI To switch on the set, press the on/off key. A green indicator comes on and the screen lights up. Go straight to the Quick Installation chapter. If the TV remains in standby mode(red indicator), press the P # key on the remote control. The indicator will flash when you use the remote control. keys and validate with ¬. “ The search starts automatically. All the available TV programmes and radio stations will be stored. This operation takes a few minutes.The display shows the progress of the search and the number of programs found. At the end of the search, the menu disappears. To exit or interrupt the search, press H. If no programme is found, consult the possible solutions p. 10. ‘ If the transmitter or cable network sends the automatic sort signal, the programs will be numbered correctly. In this case, the installation is complete. ( If this is not the case, you need to use the Sort menu to number the programs correctly. Some transmitters or cable networks broadcast their own sort parameters (region, language, etc.). In this case, indicate your choice using the iI keys a...
Questo manuale è adatto anche per i modelli :TV - 14PF7846/12 (3.69 mb)