valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
12 mm screws (4) I M6 . 20 mm screws (4) J M6 . 35 mm screws (4) K M6 spacers (4) L M6 washers (4) Lag bolt bag M Wall anchors (3) N 5/16 in. (7.9 mm) washers (3) O 5/16 in. . 2 . in. lag bolts (3) 1 Attach the TV brackets Option 1: Attaching to a TV with a flat back surface Attach the left and right TV brackets (B and C) to the back of the TV using: The M4 washers (G) and the M4 screws (D). Or The M6 washers (L) and the M6 screws (H or I). Tools you will need: • Power drill • 3/16 in. wood drill bit • . in. masonry drill bit • Phillips screwdriver • Level • Socket wrench with . in. socket or adjustable wrench • Pencil • Stud finder • Awl 2 Install the wall plate Option 1: Installing to a wood stud wall 1 Locate the stud. Verify the center of the stud with an awl or thin nail or use an edge to edge stud finder. 2 Level the wall plate (A) and mark the hole locations. 3 Drill the pilot holes as illustrated. 4 Align the wall plate (A) with the pilot holes, then place the washers (N) over the holes. Insert the lag bolts (O) through the washers, then tighten the lag bolts only until the washers are pulled firmly against the wall plate. DO NOT over-tighten the lag bolts (O). CAUTION: Avoid potential injuries or property damage! Any material covering the wall must not exceed 5/8 in. (16 mm). Option 2: Attaching to a TV with a rounded back surface Attach the left and right TV brackets (B and C) to the back of the TV using: The M4 spacers (F), M4 washers (G), and the M4 screws (E). Or The M6 spacers (K), M6 washers (L), and the M6 screws (J). Lag Bolt Bag M4 M4 M6 M6 5/16 in. 5/16 . 2. in. M4 Bag M4 . 12 mm M4 . 30 mm M6 Bag M6 . 12 mm M6 . 20 mm M6 . 35 mm or or or or 5/8 in. (<16 mm)** 2.5 in. (63.5 mm)* *Drill the pilot hole to a depth of 2.5 in. (63.5 mm) **Maximum thickness of any material covering the stud or concrete surface. NOTE: Determine if there is sufficient space between the back of the TV and the wall to connect all your cables before proceeding. You may need to use the optional spacers to allow more clearance between the back of the TV and the wall. or or or NOTE: Adjust to shorten or hide the cords LOW-PROFILE TV MOUNT I QUICK SETUP GUIDE I DX-TVM112 3-year limited warranty Visit for details. We’re here for you For customer service, call: 800-305-2204 (U.S./Canada markets) 01 800-926-3020 (Mexico market) © 2010 BBY Solutions, Inc., All Rights Reserved. Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richfield, MN USA 55423-3645 Best Buy Imports, S. de R.L. de C.V. Av. Santa Fe 485, Segundo Piso, Colonia Cruz Manca, Programa Parcial de Desarrollo Santa Fe, Delegacion Cuajimalpa, Distrito Federal, Mexico 05349 © 2010 Best Buy UK Distributions Limited. All rights reserved. Distributed by Best Buy Europe Distributions Limited. 1 Portal Way, London W3 6RS DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners. 6907-002010 <00> ENGLISH 10-0164 Option 2: Installing to a solid concrete or concrete block wall 1 Level the wall plate (A) and mark the hole locations. 2 Drill the pilot holes as illustrated. 3 Insert the concrete wall anchors (M) into the pilot holes and make sure that the anchors are seated flush with the surface. 4 Align the wall plate (A) with the wall anchors, then place the washers (N) over the holes. Insert the lag bolts (O) through the washers, then tighten the lag bolts only until the washers are pulled firmly against the wall plate. DO NOT over-tighten the lag bolts (O). CAUTION: Avoid potential injuries or property damage! Any material covering the wall must not exceed 5/8 in. (16 mm). 3 Mount the TV to the wall Slide the upper notches on the TV bracket over the upper flanges on the wall bracket. 4 Remove the TV from the wall HEAVY! You will need assistance with this step. CAUTION: To prevent property damage or personal injury, never drill into mortar between blocks. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS CAUTION: Do not use this product for any purpose not explicitly specified by Dynex. Improper installation may cause property damage or personal injury. If you do not understand these directions, or have doubts about the safety of the installation, contact Customer Service or call a qualified contractor. Dynex is not responsible for damage or injury caused by incorrect installation or use. The weight of your TV must not exceed 50 lb (22.7 kg). The wall must be capable of supporting five times the weight of the TV and wall mount combined. This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children! 5/8 in. (<16 mm)** 2.5 in. (63.5 mm)* *Drill the pilot hole to a depth of 2.5 in. (63.5 mm) **Maximum thickness of any material covering the stud or concrete surface. Latched Unlatched ...