valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
And then hook the brackets over the top of the wall mount. Rotate the display let the bottom of the brackets hook over the bottom of wall mount, as shown in Fig.3a. Then put safe bolts into the bottom of the brackets and lock it, as shown in Fig.3b. Step display Thank you for choosing our products -8- If don’t understand about right install ways, please consult to normal installing specialist. IMPORTANT: Item No.:PSW449T Multifunctional double deck wall mount Tilt Flat Panel TV Bracket Easy installing: Just hang up the display Safety: locking by spinning bolt on the bottom Max load capacity:60kg/132lbs TV size range: 23 ~36 Adjustable angle: 5 15 " " - ~ Inside has balance adjust system Bulit in leveler system INSTALLATION GUIDE 4 Fig 3a 2,3 1 Fig 3b UP UP MADE IN CHINA Pyle Audio 1600 63rd st , Brooklyn, NY, 11204 (718)236-8000 After determining the height of stand, follow the installation instructions in below to install wall mount to different kinds of wall -wooden, concrete. Using a awl or nail to make where the nails are located, as shown as fig.2b. Distance between two nails for fixing wall mount must not less than 12”. Pre-drill these holes with a 5mm drill bit to at least 50mm in deep hole. Please make sure these holes are level and located at center. Use wall mount as a template to mark the location of other three holes and drill the same holes. Fix the wall mount to the wall with 4 long bolts(H) and washers(J). Wooden wall: -2- -7- Hardware List: Actual parts appearance and the quantity may different with illustrated. 6 6 H I J K 6 4 Square washer Long bolt Wall anchor Long bolt washer Spacer ID Description 1 2 A 3 B C 1 1 4 1 4 4 Wall mount Left bracket Right bracket M4.12mm bolt M4.16mm bolt M5.16mm bolt M6.16mm bolt M5.36mm bolt M6.36mm bolt Qty D 4 4 4 4 E F G 4 2 Safe bolt A-F G H I J K ID Qty Description Fig 2b Fig 2c Concrete wall: Using the wall mount as template to mark 6 holes location on the wall. There holes are located at the top row of the slots and three more are located at the bottom row. The outer holes must be fall to the left and right of the two holes in the middle of the mount. Please make sure these holes are level and at least 6” between any two lines. Pre-drill these holes with a 10mm drill bit to at least 50mm deep hole. Insert wall anchors(I) into each of these holes. Attach the wall mount to the wall using 6 long bolts(H) and washers(J). 1 2 3 4 Using balance-adjusting system on the plate, make sure whether wall plate is installed balance. If not, then slide the wall plate let pointer level in the center position. H J 1 Balance-adjusting UP UP b 15 degr ee viewing angle eyelevel a Fig 2a Step2: mounttowallFirst, determine the height of stand The best height of stand is parallel to eyelevel of a person who sitting on a couch. Normally, the horizontal distance of eyelevel is about 4’ from ground level. The following two conditions are for determining the perfect height of stand: 1) the distance between wall and couch(Fig 2a). 2) the distance of eyelevel from ground level plus the distance measured from eyelevel of a person sitting on couch with viewing angle of 15 ( Fig 2a). For example: 1) the distance of ‘a’ is 5’-7’, the distance of ‘b’ is about 1’ 2) the distance of ‘a’ is 8’-13’, the distance of ‘b’ is about 3’ 3) the distance of ‘a’ is 14’-17’, the distance of ‘b’ is about 4’ The perfect height of stand centre will be anywhere within b, where you feel comfortable for viewing. ° AttachStep 2: Attach mount to wall WARNING We are not responsible for any personal injury or product damage due to mishandling, incorrect mounting, incorrect assembly or incorrect use of this product. The supplied wall mounting hardware is not for use on steel stud walls or cold cinder block walls. If you are uncertain about the nature of your wall, please consult a qualified contractor. If the hardware you required is not included please contact your local hardware store. Note: Caution: This Product LCD / Plasma Wall Mount Bracket is intended for use only with the maximum weights indicated . See apparatus instructions .Use with products heavier than the maximum weights indicated may result in instability causing possible injury . Caution: UP Fig. 1UPStep1: Attachbracket toTVCheckyourTVmanualtoconfirm thediameter of bolt to be usedorchoosean appropriate bolt according to size, height and position of the holes on your TV. See pages 4-5 of these instructions for examples. For correct installing, make sure that hook of every bracket must facing down. Use selected bolts, spacers and washers for installing bracket at the back of display. Adjust two brackets to equal heights and level. Once aligned, tightly secure the bolts. As shown in Fig.1. Don't force the bolt into the hole, which will cause a damage of equipments and injure of person. Don't use electric drill to fasten any bolts. Note: the UP side on the top" " . IMPORTANT: Step 1: Attach bracket to TV IMPORTANT Note: Fig. 1 U...