Fasten all bolts and screws securely. Failure to do so may cause the plasma display and Wall Mounting Unit to fall down, causing potentially fatal accidents. Improper positioning/installation of the Wall Mounting Unit on the wall may cause the unit to fall down. Check the structure, material, and strength of the mounting surface thoroughly and carry out installation in a suitable location. Failure to do so may cause the plasma display and Wall Mounting Unit to fall down, leading to potentially fatal accidents. Mounting the Plasma Display Danger Position of Wall Mounting Holes wWall Mounting Unit Wall Surface Side (Wall Mounting Unit) eScrews (M5X30) x 10 Align the first Mounting Hole Plasma Display 3. Identify the Rotation Shaft Screws of the Wall Mounting Unit. Check that the left and right Rotation Shaft Screws are secure, as the Rotation Jaw of the Frame (attached to the plasma display) will be inserted into the Rotation Shaft Screw Component of the Wall Mounting Unit w. Avoid inserting fingers into the gap between the Frame and the Wall Mounting Unit when putting these together, as fingers will get trapped, causing injury. Caution 4. Attach the plasma display to the Wall Mounting Unit. *This task must be performed by at least two persons. Insert the Rotation Jaw of the Frame q (attached to the plasma display) securely into the Rotation Shaft Screw Component of the Wall Mounting Unit, then raise up the plasma unit on this axis and push it into place - it should lock with a clicking sound. Before releasing the unit, check that the plasma display is securely fitted and does not rattle and loose. w Wall Mounting Unit Rotation Shaft Screw Component Rotation Shaft Screw Spacer Ring Rotation Jaw q Frame Rotation Jaw 3. Identify the Rotation Shaft Screws of the Wall Mounting Unit. Check that the left and right Rotation Shaft Screws are secure, as the Rotation Jaw of the Frame (attached to the plasma display) will be inserted into the Rotation Shaft Screw Component of the Wall Mounting Unit w. Avoid inserting fingers into the gap between the Frame and the Wall Mounting Unit when putting these together, as fingers will get trapped, causing injury. Caution 4. Attach the plasma display to the Wall Mounting Unit. *This task must be performed by at least two persons. Insert the Rotation Jaw of the Frame q (attached to the plasma display) securely into the Rotation Shaft Screw Component of the Wall Mounting Unit, then raise up the plasma unit on this axis and push it into place - it should lock with a clicking sound. Before releasing the unit, check that the plasma display is securely fitted and does not rattle and loose. w Wall Mounting Unit Rotation Shaft Screw Component Rotation Shaft Screw Spacer Ring Rotation Jaw q Frame Rotation Jaw 5. Fix the Frame and Wall Mounting Unit. Combine the Frame Fastening Screws, Spacer Rings, Flat Washers, and Spring Washers (from the two pairs of Frame Fastening Screw Components that were put aside when detaching the Frame q from the Wall Mounting Unit w) as shown below and fasten them securely using a screwdriver. *Confirm that all of the parts are securely fastened and do not rattle and loose. Frame Fastening Screw Spring Washer Flat Washer Spacer Ring Avoid inserting fingers into the gap between the Frame and the Wall Mounting Unit when putting these together, as fingers will get trapped, causing injury. Caution Frame Fastening Screw Component Frame Fastening Screw Spring Washer Flat Washer Spacer Ring 5. Fix the Frame and Wall Mounting Unit. Combine the Frame Fastening Screws, Spacer Rings, Flat Washers, and Spring Washers (from the two pairs of Frame Fastening Screw Components that were put aside when detaching the Frame q from the Wall Mounting Unit w) as shown below and fasten them securely using a screwdriver. *Confirm that all of the parts are securely fastened and do not rattle and loose. Frame Fastening Screw Spring Washer Flat Washer Spacer Ring Avoid inserting fingers into the gap between the Frame and the Wall Mounting Unit when putting these together, as fingers will get trapped, causing injury. Caution Frame Fastening Screw Component Frame Fastening Screw Spring Washer Flat Washer Spacer Ring Adjusting the Angle of the Plasma Display*The angle of the Wall Mounting Unit can be adjusted to 0°, 5°, 10°, 15°, and 20°. 1. Adjust the angle of the plasma display. Brace the upper middle part of the plasma display with one hand and push the Angle Adjustment Lever to the left with the other hand. The plasma display will tip forward. Release the Angle Adjustment Lever when the desired angle setting is reached. Caution Grip the plasma display firmly while adjusting the angle, as the display could tip over and cause injury. 2. Fix the Angle Adjustment Lever. Once the plasma display has been set at the ...
)
