valutazioni - 3, GPA: 4.3 ( )

Produttore : HoMedics File Size : 1.34 mb File Nome : Lingua di insegnamento:

(1.5–2.5cm) above elbow. Center tube over middle of arm. Fit cuff securely. Allow room for two fingers to fit between the cuff and your arm. Solid Colored Line 14 13 1. If the cuff is not assembled, pass the end of the cuff furthest away from the tubing through the metal D-ring in order to form a loop. The smooth side without the felt material should be on the inside of the cuff loop. End of cuff D-ring ARROW MUST FALL WITHIN YELLOW BAND 2. Plug the cuff tube into the left side of the unit. 2~3 cm(0.8”~1.2”) Position cuff edge0.8–1.2 inches (2–3cm) above elbow. Fit cuff securely. Allow room for to fit between and your arm. Center tube overmiddle of Insert plug here 15 3. Open the arm cuff so that your arm may be placed through it. 4. Remove tight fitting clothing from around your upper left arm. 5. Position cuff edge 0.8-1.2 inches (2-3cm) above elbow. 6. Center tube over middle of arm. 7. Pull the end of the cuff so that it tightens evenly around your arm. Press the hook and loop material together to secure. Allow room for 2 fingers to fit between the cuff and your arm. 8. Lay your arm on a table (palm upward) so the cuff is at the same height as your heart. Make sure the tube is not kinked. 16 Note: If it is not possible to fit the cuff to your left arm, it can also be placed on your right arm. However, all measurements should be made using the same arm. To use on the right arm, you must position the artery symbol “ ” over the main artery. Locate the main artery by pressing with two fingers approximately 1" (2 cm) above the bend of your elbow on the inside of your right arm. Identify where the pulse can be felt the strongest. This is your main artery. Main Artery MEASUREMENT PROCEDURE Important Notes: • Blood pressure changes with every heartbeat and is in constant fluctuation throughout the day. • Blood pressure measurement can be affected by the position of the user, his or her physiologic condition and other factors. For greatest accuracy, wait 1 hour after exercising, bathing, eating, drinking beverages with alcohol or caffeine, or smoking to measure blood pressure. • Before measurement, it is suggested that you sit quietly for 15 minutes as measurements taken during a relaxed state will have greater accuracy. 17 You should not be physically tired or exhausted while taking a measurement. • During the measurement, do not talk or move your arm or hand muscles. • See page 22 for additional notes regarding your blood pressure measurement. If you are using this blood pressure monitor for the first time, please remove the protective film from the screen. 1. Press the User Select Button to choose User 1 or User 2. OR After the user number is selected, press the START/STOP button to confirm the chosen user. 2. With the cuff wrapped around your arm, press the START/STOP button. Do not inflate the cuff unless it is wrapped around your arm. All digits will light up to check the display functions. The checking procedure will be completed after about 3 seconds. 18 3. After all symbols disappear, the display will show “00”. The monitor is “Ready to Measure” and will automatically inflate the cuff to start measurement. 4. Once your systolic pressure is determined, the monitor will begin deflating to measure your diastolic pressure. Note: This monitor will re-inflate automatically if the system detects that your body requires more pressure for measurement. 5. When the measurement is completed, the cuff will deflate entirely. Systolic pressure, diastolic simultaneously on the LCD screen. pressure and pulse will be shown The measurement is then automatically stored into memory. 19 Note: 1. This monitor automatically turns off approximately 1 minute after last operation. You may also press the START/STOP button to turn the unit off. 2. To interrupt the measurement, you may press the START/STOP (recommended), “MEMORY,” User-Select or Date & Time Set ( ) buttons. The cuff will deflate immediately after a button is pressed. RISK CATEGORY INDICATOR The U.S. Department of Health and Human Services and the National Institutes of Health have developed a blood pressure standard classifying blood pressure ranges into 4 stages. This unit is equipped with an innovative blood pressure classification indicator, which visually indicates the assumed risk level (normal, prehypertension, stage 1 hypertension, or stage 2 hypertension) of each reading. Symbols are described below and classifications follow the guidelines as described earlier in this manual (page 5). (No Symbol) 20 RECALLING VALUES FROM MEMORY This monitor can be used by two individuals. Each user can store up to 50 measurements. 1. Press the User-Select button. 2. Choose User 1 or User 2. 3. Press the “MEMORY” button to access the memory. 4. The monitor will first display the calculated average applied to the last 3 memories. 5. Every new press of the “MEMORY” button will recall a previous reading. The latest reading will be recalled first. 21 CLEARING VALUES FROM MEMORY ...

Scarica la tua

Per scaricare, digitare 2 cifre :