valutazioni - 6, GPA: 3.8
(
)
)
|
Facilità d'uso
This Software is being provided to you under license, subject to the terms and conditions of this Agreement. If you use the Datalogic Product, you will be deemed to have accepted the terms and conditions of this Agreement. If you do not intend to be bound to the terms of this Agreement, Datalogic is not willing to license the Software to you, you may not use the Datalogic Product or the Software, and you must contact the party from whom you acquired the Datalogic Product for instructions. 1. Definitions. 2. Scope Of License Granted. 3. Transfers, Support. 4. Intellectual Property. 5. Proprietary Information. 6. Limited Warranty. 7. Infringement. 8. Limitation Of Liability. 9. Government Restricted Rights; International Use. 10. Termination. 11. General Provisions. - END - Installation The QuickScan® QS6500 linear imager is easy to install and use. The following figure shows the steps to perform an installation. Turn off the host computer before connection. Consult the host terminal’s manual if necessary. 12543$4.50$2.79$3.99 1.Connect the interface (I/F) cable to the linear imager. 2.Connect the I/F cable to the terminal’s communication port. 3.Connect the power cord to the I/F cable connector if required. Linear imagers that use power off the terminal (P.O.T.) do not require a power supply. 4.If required, connect the AC adapter to the wall outlet. 5.To verify operation, point the linear imager at a bar code and pull the trigger. The linear imager should emit a single beep indicating that the label has been scanned successfully. The linear imager installation is complete. Power Supply Models require either a Listed class II or class III with a Limited Power Source (LPS). For the safety certification to be valid, class III input power sources must be IEC/EN60950-1 (EN 60335- series, EN 60065 or relevant) approved. Input: 100 - 240 VAC Output: 9 - 10 VDC Max. Current: 2.0 A Max. Power: 20 W How to Scan The figure below shows the right and wrong ways to scan a bar code. 1122 1.The linear imager must be pointed at a slight angle to the bar code so that the light reflected off the bar code can be “seen” by the linear imager. Do not hold the linear imager perpendicular to the bar code. 2.The targeting beam must cross the entire label. The linear imager cannot read the bar code data without seeing the entire label. Scanning PDF417 Bar Codes (PDF models ONLY) To read a PDF417 bar code, aim the targeting beam at the top of the bar code, and in a smooth motion, scan down through the bar code. You will hear a series of ticks, followed by a final beep when the bar code’s content has been completely decoded. You may need to repeat this process if the PDF code is hard to read. Troubleshooting If the linear imager is not operating properly, the following checks should be performed: 1.Since the linear imager can receive its power from the host computer (Power Off the Terminal—P.O.T.), it will not operate without the system power on. If the linear imager uses an external power supply and the external power supply has failed, the linear imager will not operate. 2.If an external power supply is used, exchange the power supply with a known good power supply and retest the linear imager. 3.If the linear imager receives power from the host (P.O.T.), connect the linear imager to a known good host and retest. OFFON123 4.Verify that the interface cable is securely attached to the host. Consult your technical support personnel or refer to your host system manual to verify the proper connection for the linear imager. 5.Verify that the interface cable is securely attached to the linear imager. 6.Check that the labels are of sufficient quality to be recognized by the linear imager. Wrinkled, smudged, or torn labels can cause the linear imager to not read at all. Scan a known good label to check the linear imager's read operation. 7.Ensure that the linear imager's interface type is compatible with the host terminal by consulting your POS system manual and/or the linear imager’s Product Reference Guide found on the CD included with your linear imager. 56Product ReferenceGuide7 If the linear imager still does not function properly, contact your local supplier or Datalogic Customer Support Services. Compliance Statement This device complies with Part 15 rules. Operation is subject to the following conditions: 1.This device may not cause harmful interference; and 2.This device must accept any interference received, including interference that may cause undesired operation. This Class A digital apparatus complies with Canadian ICES -003. Cet appareil numerique de la classe A est confrome a la norme NMB-003 du Canada. LED Class CLASS 1 LED PRODUCTAPPARECCHIO LED CLASSE 1 LED KLASSE 1APPAREIL A LED DE CLASSE 1 EN60825-1/All:1996 Installation Le lecteur de code a barres Linear Imager QS6500 est un linear imager de poche facile a utiliser. Le schema suivant illustre la procedure d’installation du imager. Eteignez l’ordinateur avant de connecter ...