valutazioni - 2, GPA: 4 ( )

Produttore : Toshiba File Size : 1.69 mb File Nome : Lingua di insegnamento:

2- 25 2. PRINTER SETUP EO1-33030 2.10 Program Download 2.10.5 Printer Information Registration NOTE: This information is stored in printer memory before delivery to the customer, so this procedure need only be done if it is required to change any of the information. This procedure will be used to register (transfer) printer information to the printer memory and the information registered here will also be printed on every diagnostic print issued from the printer. The information to be registered will be the printer model name and the printer type. · Procedures 1. To perform this operation, you will need to turn on the power of the B-419 printer (do not hold the feed key this time). Connect the printer to the PC with the RS-232C cable. Select the TPCL-LE mode for the printer issue mode. Then set the communications parameters as follows: 19200 bps, None parity 2. From the Install Program for B-419 main menu, select Options (O) and Printer Information Store (P) as shown in the screen display of the figure below. NOTE: When the entire serial number is entered, the printer ID will appear automatically. 3. After selecting Printer Information Store (P), the screen will change to the display shown below. 2- 26 2. PRINTER SETUP EO1-33030 2.10 Program Download 2.10.5 Printer Information Registration (Cont.) 4. Click on the QQ/QP check box for the Model on the Printer Information Store display. Depending on the selected model, the printer changes the communication requirements and other internal NOTE: Model Name is automatically displayed by selecting the Model. To change the Model Name click on the Default check box to remove the check mark and it will then be possible to type in a new Model Name of up to 20 characters. functions. 5. When the desired changes have been made, click on the OK button and the following screen display will appear. Confirm the printer information on the screen display, and click on Yes to start registration. NOTE: If the Complete screen does not appear, retry from step 1. 6. When the registration terminates successfully, the following display will appear. 2- 27 2. PRINTER SETUP EO1-33030 2.10 Program Download 2.10.6 Test Print This procedure will be used to perform a test print. · Procedures 1. To perform this operation, you will need to turn on the power of the B-419 printer (do not hold the feed key this time). Connect the printer to the PC with the RS-232C cable. Select the TPCL-LE mode for the printer issue mode. Then set the communications parameters as follows: 19200 bps, None parity 2. From the Install Program for B-419 main menu, select Options (O) and Test Print (T) as shown in the screen display of the figure below. NOTES: 1. The default settings are: Label Pitch: 127 mm Print Count: 1 Sensor: Reflective 2. The size of the print image for the test print has been designed to fit to a 127 mm pitch label. Therefore, when using the paper of shorter pitch, the print image will breaks, or when using the label of longer pitch, a blank space will remain. 3. Setting the different label pitch from actual paper size or using the paper with a black mark printed on an improper position may cause an error. 3. When the following screen display appears, set the Label Pitch, Print Count, and the Sensor, then click on the OK button. Reflective A few seconds later, the printer will start the test print. 2- 28 2. PRINTER SETUP EO1-33030 2.10 Program Download 2.10.7 Version Display This procedure will be used to check the version of the Install Program for B-419 Standard. · Procedures 1. From the Install Program for B-419 main menu, select Help (H) and Version (A) as shown in the screen display of the figure below. 2. The Version screen display will appear as follows. 2- 29 3. MAINTENANCE EO1-33030 3.1 Cleaning 3. MAINTENANCE WARNING! 1. Be sure to disconnect the Power Cord before performing maintenance. Failure to do this may cause an electric shock. 2. To avoid injury, be careful not to pinch or jam your fingers while opening or closing the cover. 3. The Print Head may become hot. Do not touch the Print Head. 4. Do not pour water directly onto the printer. 3.1 Cleaning 3.1.1 Print Head/Platen CAUTION! 1. Do not allow any hard objects to touch the print head or platen, as this may cause damage to them. 2. Do not use any volatile solvent including thinner and benzene, as this may cause discoloration to the cover, print failure, or breakdown of the printer. 3. Do not touch the print head element with bare hands, as static may damage the print head. 4. Failure to clean the print head may cause a print head problem, shortening its life. 5. Failure to clean the platen may cause the platen to slip, resulting in a feed error. NOTE: For cleaning the print head, TOSHIBA TEC-approved print head cleaner is recommended. It is available at your nearest TOSHIBA TEC sales agent. Part Name: Print Head Cleaner Part No.: 24089500013 This chapter describes how to perform normal maintenance. To maintain the printer perf...

Scarica la tua

Per scaricare, digitare 2 cifre :