valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Do not use tapes that do not have the mark. • Tapes are available in three different widths: 1/4” (6 mm), 3/8” (9 mm) and 1/2” (12 mm). • Do not pull the tape since this may damage the tape cassettes. • Do not attempt to cut the tape while printing or feeding since this will damage the tape. • Do not clean the machine with alcohol or other organic solvents. Use only a soft, dry cloth. • Remove the batteries if you do not intend to use the machine for an extended period of time. Note: If power is disconnected for more than three minutes, all text shown in the display and any text files stored in the memory will be lost. • Do not put any foreign objects into or anything on the machine. • Do not expose the machine to high temperatures or high humidity. Never leave it on the dashboard or in the back of your car. • Do not use the machine in dusty places, and keep it out of both direct sunlight and rain. • Do not leave any rubber or vinyl on the machine for an extended period of time. Doing so may cause staining. • After inserting a new tape cassette, advance the tape by holding down and pressing once. • Do not touch the print head mechanism. If the head is touched, clean it immediately with a soft wipe (e.g., a cotton swab) to avoid permanent damage. • To avoid injuries, do not touch the cutter’s edge. • To prevent damage during shipment, a clear protective sheet is placed over the LCD panel. Remove this clear protective sheet before beginning use. POWER SUPPLY Changing the batteries CAUTION Batteries installed incorrectly can overheat and leak. Can result in chemical burns and machine overheating and damage. Your machine requires 6 alkaline AAA batteries. Carefully follow these instructions. 1 Press bumps on top of back cover and open. 2 Pull out tape cassette, if one was installed. 3 Remove batteries, if they were already installed. 4 Hold machine as pictured: 5 Insert six new batteries as follows: Always: • Insert “+” ends before “-” ends. • Remove “-” ends before “+” ends. • Replace all 6 batteries at the same time with new ones. 6 Insert tape cassette. 7 Insert two hooks on bottom end of back cover into slots on bottom of machine. Push down firmly on cover until it snaps into place. 8 Turn machine on. If no power, immediately remove batteries and call Brother Customer Service at: 1-877-478-6824 OVERVIEW Display Backspace key CURSOR MOVEMENT You can view and edit different parts of the text by moving the cursor backward and forward. To move the cursor one character at a time, press or . To move the cursor to the beginning of the text, hold down and press . To move the cursor to the end of the text, hold down and press . BACKSPACE KEY This key can be used to remove characters from your text, clear all of the text or cancel the current function and return to the text input mode. To delete the character to the left of the cursor or to cancel a function, press . To clear all of the text that is currently entered, hold down and press . SPACE KEY As on a word processor, press to add a blank space to your text. RETURN KEY Press when you wish to accept or confirm a setting, or end the first line of text and start the second. To add a second line, press once. The return mark ( ) appears in the text to indicate the end of the first line and the beginning of the second. Note: Two lines of text can only be entered if 3/8” (9-mm)- or 1/2” (12-mm)-wide tape is installed. To accept or confirm a setting from a list, press once. ACCENTED CHARACTERS You can also choose from a list of other accented characters that can be added to your text. 1 Press if you want the accented character to be an uppercase letter. Note: To quit the following procedure at any time without making any changes, press . 2 Hold down and press . The message “A-U?” appears in the display. 3 Press the key for the letter in the accented character that you wish to add, and then press and until the cursor is positioned under the desired accented character. 4 Press to add the selected character to your text. SYMBOLS In addition to the letters, symbols, and numerals on and above the keys, there are 72 symbols available with the Symbol function. These symbols are divided into 9 groups, corresponding to the letters A through I. 1 Press . The message “A-I?” appears in the display. 2 Press the key for the letter of the group containing the symbol that you wish to add, and then press and until the cursor is positioned under the desired symbol. 3 Press to add the symbol to the text. With your new PT-1180, you can create labels for any application. Select from the many frames, character sizes and styles to design beautiful custom labels. In addition, the variety of tape cartridges available allows you to print labels with different widths and exciting colors. You no longer have to worry about urgent tasks that require professional printing. In the office, the factory, the lab or the home, the quality and performance of the PT-1180 make it an extremely practical...