valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
For Windows ® 11 For Macintosh 6 If the dialog box warning that the software has not 7 In the dialog box that appears, indicating that installapassed Windows Logo testing appears again, click the tion is finished, select “Yes, restart immediately.”, and Continue Anyway button to continue with the then click the Finish button. After the computer is installation (since this printer driver has already restarted, the installation is fully completed. cleared strict product quality standards of our testing). 8 Remove the CD-ROM from the computer. P-touch Editor Version 3.1 Installation (for Macintosh) Follow the procedure below to install the P-touch Editor software on the Mac. The Mac version of the software is for a Mac with an English operating system. If the software is installed on a Mac with an operating system in a different language, the software may not run properly. Check that your system configuration meets the following requirements. Computer: Macintosh or Power Macintosh Operating system: Serial interface: Macintosh equipped with a PowerPC processor and a serial port (modem or printer), and running Mac OS 8.1 or later USB interface: Macintosh equipped with a USB port and running Mac OS 8.5.1 or later * For previous Mac OS versions, refer to the Apple Web site for information about USB. * This software can only run on Mac OS X in the Classic environment. However, the Mac OS X v10.2 Classic environment is not supported. * The application is supplied on a CD-ROM; therefore, the computer should be equipped with a CD-ROM drive. Hard disk free space: At least 20 MB • A few hundred megabytes of additional free space may be needed when printing long labels or large amounts of data. Port: Serial or USB Available memory free space: Minimum 24 MB CD-ROM drive With the enclosed CD-ROM, the following can be installed: • P-touch Editor Version 3.1 • PT-9200DX printer driver Installing P-touch Editor Version 3.1 5 After the installer starts up, select the installation method. 1 Connect the PT-9200DX to the Macintosh using the enclosed interface cable. Be sure to leave the PT- Clicking the Install button immediately starts installing 9200DX turned off. the most basic options. (Some clip art illustrations are 2 Turn on the Macintosh. not installed.) About 20 MB of available hard-disk space is needed 3 Insert the P-touch Editor CD-ROM into the computer’s to begin installation. In order to install all options, CD-ROM drive. about 120 MB of available hard-disk space is needed. 4 Double-click the P-touch Editor 3.1 Installer icon in If enough hard-disk space is available, click the Installthe folder that appears. button. 12 Installing the PT-9200DX printer driver 1 Double-click the Driver Installer icon in the P-touch folder. For Macintosh Clicking the Custom Install button displays a dialogue box that allows you to select which options to install. Only the options with a check mark beside them are installed. Select the options that you wish to install, and then click the Install button. Dialogue box that appears if the Custom Install button is clicked: 6 Installation begins. 7 When the installation is finished and the following dialogue box appears, click the Quit button. 8 When the dialogue box appears, asking if you wish to restart the computer, click the Quit button to continue and install the printer driver. 2 After the installer starts up, click the Select Driver button. 3 In the dialogue box that appears, select “PT9200DX( USB)” (for a USB port connection) or “PT- 9200DX(Serial)” (for a modem or printer port connection). The printer drivers with a check mark beside them are installed. Then, click the Install button. 4 Installation begins. When the installation is finished and the following dialogue box appears, click the Quit button. 5 When the dialogue box appears, asking if you wish to restart the computer, click the Restart button to restart the computer. 6 After the computer is restarted, turn on the P-touch. 13 Selecting the printer 3 If the PT-9200DX(Serial) icon was selected, click the icon for the port linked with PT-9200DX(Serial) from 1 Pull down the Apple menu and select “Chooser” to the list on the right. display the Chooser window. For Macintosh 2 In the list on the left, click the PT-9200DX(USB) icon 4 Close the Chooser window to confirm your settings. (for a USB port connection) or the PT-9200DX(Serial) icon (for a modem or printer port connection). Then, select the appropriate printer driver. Uninstalling P-touch Software and Printer Driver Uninstall P-touch Editor Version 3.1 and the printer driver using the steps below: Uninstalling P-touch Editor Version 3.1 (for Windows® 95/98/Me/NT 4.0/2000 Professional/XP) 5 A message appears, asking if you wish to delete the selected application. Click the Yes button to delete the application. If you do not wish to delete the 1 Start up Windows® 95/98/Me/NT 4.0/2000 Professional/XP. 2 Click the Start button in the taskbar, select “Settings”, and then click “...