valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THIS PLUG! • Voltage: 208VAC or 240VAC depending on model ordered • Frequency: 60 Hz (non-CE) or 50 Hz (CE and Australian models) • Phase: Single • Service: 30 Amp Setup: Setup of the toaster consists of unpacking the unit, placing it on a sturdy table or countertop adjacent to a properly grounded AC outlet of appropriate voltage, removing the cardboard packing inserts, installing the bun feeder in the slot on top of the cover, and plugging it in. NOTE: The cover must be closed to install the bun feeder, and the bun feeder must be removed to open the cover. The unit is shipped with a programmed setpoint of 550°F (288°C), upper crown compression knob set to 4, lower crown compression knob set to 5, upper heel compression knob set to D, and lower compression knob set to E. The operator may change these settings to attain desired toasting. 4. Operation 1. Press the ON/OFF button once. The temperature in degrees Fahrenheit will appear in the green LED display window. To view the current setpoint, press the button. The word LOW will appear in the green LED display window. The unit will take about 10 minutes to reach operating temperature, at which time the display will change to REDY, indicating the toaster is ready for use. 2. Load buns into the appropriate slots (Heel or Crown) one at a time, with the cut faces toward the rear of the unit. The unit will toast the buns and transfer them to the holding tray. 3. Adjust the setpoint and bun compression as necessary to achieve desired toasting. 5. Viewing and Adjusting The Setpoint To view the platen temperature: Press the button twice. The setpoint in degrees Fahrenheit will be displayed in the green LED display window. LOWER SETPOINT BUTTON ON/OFF BUTTON LED DISPLAY RAISE SETPOINT BUTTON DISPLAY TEMPERATURE BUTTON 550F To change the display from Fahrenheit to Celsius: Unplug the unit, then press and hold the button as the unit is plugged back in. To change the setpoint: 1. Turn the unit OFF (press the button). Enter the setpoint programming mode by pressing the , , , buttons in that order. The current setpoint will appear in the LED display. To increase the setpoint, press the button; to decrease it, press the button. 2. When the desired setpoint is displayed, press the button once. Press the ON/OFF button. If the platen is within 20°F (11°C) of the setpoint, the display will show REDY. Otherwise, the display will show LOW or HIGH until the platen is within 20°F (11°C) of the setpoint, at which time the display will change to REDY. 3 4 6. Adjusting Bun Compression 1. There are two pairs of compression adjustment knobs (one pair numbered 1-5, the other lettered AE), as shown in the accompanying illustration. Factory settings are circled. UPPER COMPRESSION LABEL Crown Compression Adjustment (1-5) Crown Compression Adjustment (1-5) Heel Compression Adjustment (A-E) 2. Settings A and 1 cause the greatest bun compression (that is, the thinnest bun after toasting). 7. Changing Belts 1. Turn the unit off (press the ON/OFF button) then unplug it. If the unit has been in operation, allow it to cool for about 1. hours. TIP: Change belts in the morning, prior to turning the toaster on. 2. Remove the bun feeder, and then open the cover. 3. Set the bun compression knobs to positions E and 5. 4. Press down on the top roller and move it to the retracted (down) position. (NOTE: Each side of the roller must be locked down.) 5 5. Rotate the tray stabilizer latch upward to unlatch it. Tray Stabilizer Latch 6. Slip the old belt off the rollers and slip the new belt on. When the replacement belt has been properly positioned between the raised edges of its rollers, rotate the tray stabilizer latch to the latched position. 7. Press down on the top roller to unlock it and allow it to extend. 8. Close the cover. Return the bun compression knobs to their previous settings. 8. Operator Troubleshooting PROBLEM PROBABLE CAUSES CORRECTIVE ACTION PRO1 in LED display. A. Indicates failure of main platen probe or associated circuitry. A. Call FASC. PRO2 in LED display. B. Indicates failure of holding tray resistor. B. Call FASC. A. Cover not properly installed. A. Make sure cover is correctly positioned so that the cover interlock switch is depressed. B. Toaster not plugged in. B. Plug toaster in. C. Store circuit breaker tripped. C. Reset circuit breaker. Bun conveyors do not start when ON/OFF button is pressed. D. Failed cover interlock switch, failed high limit, failed motor, or failed controller. D. Call FASC. Toasting is consistently too dark or too light. A. Improper setpoint programmed and/or incorrect compression knob setting. A. If toasting is too dark, lower the setpoint and/or compression setting until desired toasting is achieved. If toasting is too light, increase setpoint and/or compression setting until desired toasting is achieved. PROBLEM PROBABLE CAUSES CORRECTIVE ACTION Buns are too thick or too thin. A. Compression knobs on an imp...
Questo manuale è adatto anche per i modelli :Toasters - CT16 (1.03 mb)