valutazioni - 4, GPA: 4.5
(
)
)
|
Facilità d'uso
(17.7/20.5 kg) 45 Lbs./52 Lbs. (20.5/23.6 kg) Electrical information - AT-10BT & AT-5 Each toaster is equipped with a 4 foot (122 cm), 3 wire grounded power supply cord which terminates with a 3 prong plug (5-15P). MODEL NUMBER AT-10BT AT-5 Overall Dimensions with Superfeeder 14"H X 15 5/16"W x 21 5/8"D (35.6. cm x 38.9 cm x 55 cm) 14"H X 15 5/16"W x 21 5/8"D (35.6 cm x 38.9 cm x 55 cm) Stock Number/Electrical 120V-1760W-14.7 amps 120V-1440W-12.0 amps Productivity (Fresh Product) Bun Halves per hour Bread/toast sliced per hour (120V) - 600 Net/Shipping Weight 39 Lbs./45 Lbs. 17.7/20.5 kg 39 Lbs./45 Lbs. 17.7/20.5 kg 10 Electrical information - AT-200 Each toaster is equipped with a 4 foot (122 cm), 3 wire grounded power supply cord which terminates with a 3 prong plug (6-50P). MODEL NUMBER AT-200 Overall Dimensions with Superfeeder 18 3/8"H X 15 3/4"W x 26 1/2”D (46.7 cm x 40 cm x 67.4cm) Stock Number/Electrical 208V-5600W-27.0 amps 230V-5145W-22.4 amps-50 Hz 240V-5600W-23.4 amps Productivity (Fresh Product) Bun Halves per hour Bread/toast sliced per hour Croissants per hour English muffins per hour ( 208V/240V )-1200 ( 208V/240V )-1400 ( 208V/240V )-1400( 208V/240V )-1000 Net/Shipping Weight 68 Lbs./75 Lbs. (30.9/34.1 kg) INSTALLATION - AT SERIES A. UNPACK UNIT 1. Remove unit from shipping carton, unwrap loose parts and remove any packing tape. 2. Refer to the illustration below and account for the following parts: a) (4) legs -wrapped, internal package b) Bread Slide -shipped in place c) Bread Drawer -shipped in place d) Reflector/Crumb Tray -shipped in place e) Superfeeder (optional) -wrapped, internal package f) Instruction manual -wrapped, internal package B. ASSEMBLY 1. Lay the toaster on its side and install four adjustable legs into threaded holes in base. Tighten legs with crescent wrench. The unit may be leveled by unscrewing the lower insert of each leg. Precise leveling is not required for proper operation of the toaster. Set the toaster upright. CAUTION: DO NOT OPERATE THE TOASTER WITHOUT THE LEGS INSTALLED. 2. Refer to the illustration and check that the Reflector/Crumb Tray is in the proper position. CAUTION: DO NOT OPERATE THE TOASTER WITHOUT, THE REFLECTOR/CRUMB TRAY IN POSITION UNDER THE CONVEYOR CHAIN. 3. Check that the Bread Drawer is positioned flat on toaster base and pushed to ths rear until it stops. (Note: Bread Drawer is installed or removed by lifting the front handle at an angle so that the rear edge of drawer slides under the two front internal studs on right and left sides of toaster walls.) 4. Check that the Bread Slide is situated internally so that the '''tabs'' on each side are' resting behind the two rear internal studs on right and left sides of toaster walls. The front edge of the Bread Slide rests on top of the two front internal studs on right and left sides of the toaster walls. The Bread Slide should be covering the rear portion of the bread drawer. 5. Attach the optional Superfeeder on the, rod and pins located in front of the conveyor belt as shown in the illustration. Superfeeder Reflector/Crumb Tray Bread Slide Bread Drawer Studs Legs 11 C. INSTALLATION 1. Place the toaster on a flat surface and in such a way that the unit's vents are not blocked. Air must circulate under and through vent provided on the base, left side and at the rear of the unit. A minimum clearance of one inch (1", 2.6 cm) is required on the base and two inches (2", 5.2 cm) on the left side and rear of unit. Overhead clearance should allow heat to be dispelled adequately. 2. Locate the unit near a wall receptacle of the proper configuration. DO NOT USE AN EXTENSION CORD. Plug the power supply cord into an outlet of the voltage specified on the unit's rating label plate. Outlets must be grounded properly. CONVERTIBLE AT SERIES TOASTER To convert an ATToaster from front return to rear exit, follow steps indicated in Figures 1 to 3. Figure 1: 1. Turn off unit and let cool. 2. Remove Breadslide through front of unit. 3. Extra line if needed. Figure 2: 1. Flip Breadslide over. 2. Insert Breadslide through back opening. 3. Place on conveyor belt. Figure 3: 1. Turn on unit. 2. Conveyor belt will move Breadslide to rest on locator pins. 3. Ready to operate in rear exit mode. FIGURE 1 FIGURE 2 FIGURE 2 12 OPERATING INSTRUCTIONS A. PREPARATlON/WARM-UP: 1. Main Power: Turn toaster on by pressing the Main Power switch up. Turn the toaster off by pressing the Main Power switch down. 2. Temperature: Set the Top Heat knob and the Bottom Heat knob to the 6 setting (mid range) for warm-up. (Power to the heating elements is off when these knobs are in the off position.) Not available. on AT-5 Model. 3. Speed: Set the Conveyor Speed Knob to the 5 setting for warm-up. 4. Stand-By: Set the Stand-By switch to Full Heat. Not available on AT-5 Model. 5. Warm-Up Time: Warm-up time is approximately 7 minutes. B. USE/SPECIALFEATURES 1. Product: Place product on the conveyor. It will automatically be drawn through the to...
Questo manuale è adatto anche per i modelli :Toasters - AT/BT Series (291.03 kb)