Log:
valutazioni - 1, GPA: 5 ( )

Istruzioni per l'uso APW Wyott, Modello fastrac FT 1000

Produttore : APW Wyott
File Size : 269.18 kb
File Nome : f9a70e24-f08d-4144-885a-365b09b5b3a6.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


! 3 ! ! CAUTION: The National Sanitation Foundation (NSF) requires that units over 36” (91 cm) in length or weighing more than 80 lbs. (36 kg) to be either sealed or raised on the installation surface. If this unit cannot be sealed at the point of use, 4” (10 cm) legs are included to allow for proper cleaning access below unit. ! ! ! ! ! ! ! GENERAL INFORMATION I. Consult the rating label for model and serial number. Write this information below before proceeding: A. Model # __________________ B. Serial # __________________ II. Overall Dimensions w/Wire Feeder -14.6" H (371mm) x 16.2" W (411 mm) x 26.5" 0 (674mm) III. Product Opening -1.5" H (38mm) x 10.50" W (267mm) IV. Productivity (per hour) -results will vary depending on line voltage and bread dryness. V. Electrical Requirements A. Single phase, 208-240 volts, 3330 watts, 15.9 amps. B. Cordset configuration 1. Each toaster is equipped with a three-wire grounded cordset and standard three-prong plug. 2. In the United States, a four foot cordset with NEMA6-20Pplug. 3. In Canada, a six foot cordset with NEMA6-20Pplug. Net/Shipping Weight -48Ib.(21.8kg) /56Ib.(25.5kg) INSTALLATION INSTRUCTIONS I. Check Contents -refer to Figure 1, account for the following parts: A. Toast Drawer -shipped in place B. Reflector Tray -shipped in place C. Wire Feeder -inside Reflector Tray D. Instruction Manual - shipped loose NOTE: DO NOT OPERATE THE TOASTER WITH THE REFLECTOR TRAY REMOVED FROM ITS POSITION II. Position Wire Feeder -refer to Figure 2 A. Pull out Reflector Tray B. Rotate Wire Feeder C. Slide Reflector Tray back D. WARNING: Operating the toaster without the Reflector Tray reduces toasting capabilities. 4 figure 2 WARNING: Genuine APW Wyott Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in APW Wyott equipment. It is essential to use APW Wyott Replacement Parts when repairing APW Wyott equipment. Failure to use APW Wyott Replacement Parts may subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn. CAUTION: Locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or it’s contents from accidentally falling, and strong enough to support the weight of the unit and food. WARNING: Failure to provide clearances will cause unit failure and invalidate warranty claims (see installation instructions). III. Toaster Placement A. Locate the toaster near a grounded receptacle of the proper configuration (see below). Plug the cordset directly into receptacle (DO NOT USE AN EXTENSION CORD). 1. In the United States, NEMA6-20R. 2. In Canada, NEMA6-20R. B. Place the toaster on a flat surface providing the following minimum clearances: 1. Base = one inch (provided with legs installed). 2. Side and back walls = one inch 3. Overhead = Enough space to allow adequate heat displacement. 4. WARNING: Failure to provide these clearances will cause unit failure and invalidate warranty claims. C. Position toaster where customers will not contact any surface labeled "CAUTION HOT". NOTE: DO NOT OPERATE THE TOASTER WITH THE LEGS REMOVED. OPERATION INSTRUCTIONS I. PREPARATION A. Clean the toaster thoroughly before first use (See cleaning instructions). B. Controls Familiarity 1. Main Power Switch -four (4) position rotary switch a) Full Power: rotary switch turned RIGHT ( 3 o'clock). ( HIGH) b) Power Off: rotary switch turned to TOP or BOTTOM. (12 and 6 o'clock) (OFF) c) Standby Power: rotary switch turned LEFT (9 o'clock). ( STANDBY) 2. Conveyor Speed Control: Set knob to the five (5) position for warm-up. C. Temperature Settings: Set both Top and Bottom heat knobs to 12 (max.) for warm up. One (1) is the minimum heat setting. Power to the heating elements is off when the knobs are in the OFF ( 0 ) position. D. Warm-up time: Allow fifteen (15) minutes. II. NORMAL USE A. Loading Product 1. Place product on the Wire Feeder. The conveyor will automatically draw product through the toaster at a speed determined by conveyor speed control. B. Toasting Darkness: determined by conveyor speed. 1. Darkest toasting -set conveyor speed control to one (1). 2. Lightest toasting -set conveyor speed control to ten (10). 3. Other factors affecting toasting darkness. a) Product moistness -moister product requires slower speeds b) Sugar content in product -product with more sugar requires slower speeds c) Product Temperature -cooler product requires slower speeds 4. For best results, use day old bread stored at room temperature. C. The conveyor belt, drive motor, and shaft bearings do not require lubrication. CLEANING INSTRUCTIONS NEVER CLEAN THE TOASTER BY IMMERSING IT IN WATER. DO NOT CLEAN WITH AWATER JET. I. DAILY CLEANING A. With the toaster ELEMENTS OFF and cool, turn the toaster ON and set conveyor speed to four (4). B. U...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie