valutazioni - 3, GPA: 5
(
)
)
|
Facilità d'uso
FURTHER, FRYMASTER/DEAN AND ITS AFFILIATES WILL NOT BE LIABLE FOR ANY CLAIMS, DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE DIRECTLY OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION OF ANY MODIFIED PART AND/OR PART RECEIVED FROM AN UNAUTHORIZED SERVICE CENTER. NOTICE This appliance is intended for professional use only and is to be operated by qualified personnel only. A Frymaster/DEAN Factory Authorized Service Center (FASC) or other qualified professional should perform installation, maintenance, and repairs. Installation, maintenance, or repairs by unqualified personnel may void the manufacturer’s warranty. NOTICE This equipment must be installed in accordance with the appropriate national and local codes of the country and/or region in which the appliance is installed. NOTICE TO U.S. CUSTOMERS This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. While this device is a verified Class A device, it has been shown to meet the Class B limits. NOTICE TO CANADIAN CUSTOMERS This digital apparatus does not exceed the Class A or B limits for radio noise emissions as set out by the ICES-003 standard of the Canadian Department of Communications. Cet appareil numerique n’emet pas de bruits radioelectriques depassany les limites de classe A et B prescrites dans la norme NMB-003 edictee par le Ministre des Communcations du Canada. DANGER Improper installation, adjustment, maintenance or service, and unauthorized alterations or modifications can cause property damage, injury, or death. Read the installation, operating, and service instructions thoroughly before installing, operating or servicing this equipment. Do not operate the CT16 Toaster unless it has been properly installed and checked. Do not operate the CT16 Toaster unless all covers and access panels are in place and properly secured. Do not attempt to repair or replace any component of the CT16 Toaster unless all power to the unit has been disconnected. Use caution when setting up, operating, or cleaning the CT16 Toaster to avoid contact with heated surfaces. DANGER Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance. 1-1 CT16 SERIES TOASTER SERVICE AND PARTS MANUAL CHAPTER 1: SERVICE PROCEDURES Upper Compression Adjustment Knobs Lower Compression Adjustment Knobs Bun Guide for Heel and Crown Slots Heated Holding Tray LOWER SETPOINT BUTTON ON/OFF BUTTON LED DISPLAY RAISE SETPOINT BUTTON DISPLAY TEMPERATURE BUTTON REDY 1.1 CT16 Toaster Functional Description The CT16 Toaster is designed to produce fresh, uniformly toasted buns on an "as needed” basis. The countertop-mounted unit consists of a cabinet, a computer, a heating element and a pair of conveyor assemblies. When the unit is turned on, an electrical heating element (called a platen) is energized. The platen heats up to a programmed temperature referred to as the setpoint. At the same time, both conveyor assemblies are activated. When a bun is placed into one of the slots at the top of the cabinet, the conveyor belts gently carry it through the unit, with the cut face of the bun passing over the heated platen. As the bun passes over the platen, it is toasted. At the end of the process, the bun is deposited onto a holding tray. The computer allows the operator to adjust the setpoint to obtain desired toasting characteristics. Compression adjustment knobs also allow the operator to adjust the compression of heels and crowns as they pass through the toaster. 1.2 Power Requirements ALL ELECTRICALLY OPERATED APPLIANCES MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL ELECTRICAL CODE (ANSI/NFPA NO. 70-1990) OR THE CORRESPONDING NATIONAL CODE OF THE COUNTRY IN WHICH INSTALLED. THIS APPLIANCE IS EQUIPPED WITH A GROUNDING PLUG FOR YOUR PROTECTION AGAINST SHOCK HAZARD AND MUST BE PLUGGED INTO A PROPERLY GROUNDED RECEPTACLE. DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THIS PLUG! • Voltage: 200VAC, 208VAC, or 240VAC, depending on model ordered • Frequency: 60 Hz (non-CE )or 50 Hz (CE and Australian models) • Phase: Single • Service: 20 Amp 1.3 Replacing Components Accessing the Electronics 1. Pull the bun compression knobs off their shafts. 2. Remove the screws around the edge of the component housing cover and remove the cover. Accessing the Drive Motor and Auxiliary Transformer Carefully lay the unit on its back and remove the seven screws that secure the bottom cover in place. Removing the Conveyor Assemblies 1. Turn off and unplug the unit. 2. Remove the bun feeder then remove the cover by lifting it straight up until it is clear of its hinge pins. 3. Rotate the bun compression knobs to positions 5 and E. 4. Press down on the top roller(s) of the c...
Questo manuale è adatto anche per i modelli :Toasters - CT16 Series (1.58 mb)