valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
Divide the TOTAL DISTANCE by 10, and multiply the decimal portion by 12 to find your stride length in feet and inches. Example:You walk 23 feet and 6. inches in 10 steps. Convert to feet only = 23.542 feet (6. . 12 = 0.542). Divide by ten to get the stride length in feet = 2.354 feet. Now, convert back to feet and inches to get your stride length = 2 feet 4.25 inches (0.354 . 12 = 4.25). 10 steps 8 SETTING PROCEDURE ACCUSPLIT products use a common setting procedure known as “S1-S2-S3-S4.” Here’s how it works: Press S1 for 2 seconds: Enter the SET mode Press S2: Change the field to be set Press S3: Change the field value Press S4 for 2 seconds: Exit the SET mode You can enter and exit Set mode from any of the regular display screens. 9 Entering set mode Press and hold the S1 (MEMORY) button for 2 seconds. The display will start to flash, showing that you’ve entered SET mode. Setting Stride Length 1. You will see the mode indicator bar underneath DIST and the “in” indicator come on. The display will show a flashing number, which is your Stride Length set point (in inches). 2. Press the S3 + (MODE) button to increase the Stride Length (in increments of . inch), and press the S3( RESET) button to decrease the Stride Length. Hold the buttons down to change values quickly. 22 REPLACING THE BATTERY AND MASTER RESET When the display starts to dim or goes blank, it is time to replace the battery. If the display is not uniformly dim or blank, and appears to display “erroneous data”, do a Master Reset by pressing all 3 buttons simultaneously for 3 seconds and then release. The display should go blank, then turn all segments on, then display 0 steps in Step Mode. Note: All the settings will return to their default setting values. If you need to change the battery, the settings will also revert to default settings. To replace the battery: 1. Insert a coin into the slot on the bottom of the case, and twist to loosen the faceplate. Remove faceplate and set aside. 2. Locate the battery holder as seen on sketch. Pull out the old battery, and push a new LR-44 battery into the holder, with positive terminal (+) facing up. 3. Snap faceplate back into place, hooking the bottom two tabs first, then closing by pressing together at the top two tabs. 23 Battery 20 Set measurement mode “US” (English) or “EU” (Metric) Can be set from 0-5 steps STEP TIME DIST SET DIGI-WALKERXL.COM 140SXL S3S3+ S1,S2,S4JW200 Set Step Filter set point STEP TIME DIST SET DIGI-WALKERXL.COM 140SXL S3S3+ S1,S2,S4JW200 21 CHANGING UNITS (English vs. Metric) The Pedometer can display either in English units (in, mi, and lb -this is the default), or in Metric units (cm, km, and kg). From within Deep Set mode (see pg. 18), press the S2 button to cycle back and forth between setting the Step Filter set point and Choice of Unit System.The unit will show either “US” or “EU” (for European Union) depending on the unit system chosen. If you change units after using the pedometer, the unit will convert all of your data into the new unit system when you exit Deep Set model.You can check to see which system of units you are using by seeing which measurement units are displayed on the Stride and Weight setting screens. Press S3+ (MODE) or S3– (RESET) to change the Measurement Mode. Press and hold S4 for 2 seconds to exit Deep Set Mode. Note:The unit will save any changes and exit set mode after 30 seconds unattended. 18 OTHER SETTINGS The Step Filter and Unit of Measurement settings are accessed through a special “deep set” mode. To enter this mode, press and hold the S1 button for 4 seconds.The screen will display a single digit. From within Deep Set mode, press the S2 button to cycle back and forth between the Step Filter set point and Choice of Unit System. 19 CHANGING STEP FILTER SETTING While the JW200 PedometerEngine™ Step Sensor is extremely accurate, some people like to have the ability to filter out false steps. Therefore, the unit has a variable setting step filter, to allow fine-tuning to your specific preferences. You can set the value to any value from 0 – 5 steps. For example, if the filter is set to “3”, the unit will wait to start counting steps until more than three steps have been taken in less than five seconds. Press S3+ (MODE) or S3– (RESET) to change the Step Filter Setting. 16 VIEWING YOUR RESULTS Once you put on your pedometer with the cover closed, it will automatically begin to record your steps, activity time, and distance. Repeatedly press the MODE button to cycle through the pedometer modes: STEPS gTIME • DISTANCE • STEPS Time and Distance are counted automatically whenever steps are being counted. • TIME is time spent in step activity. • DISTANCE is simply stride length x steps. Note: For extra accuracy, the default Step Filter Setting is 1. See page 19 to learn more. 17 RESETTING YOUR PEDOMETER Most people prefer to reset counts daily.To reset your counts: From STEP,TIME, or DISTANCE mode, press and hold the yellow RESET button for at least...