valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
Have the second person hold the console assembly near the Uprights (84) as shown. Look under the console assembly and locate the Console Wire Harness (78). Cut the plastic ties securing the Upright Wire Harness (77) to the right Upright (84). Next, connect the Upright Wire Harness to the Console Wire Harness (78). See the inset drawing. The connectors should slide together easily and snap into place. If they do not, turn one connector and then try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. 3. Look under the console assembly and locate the TV cable. Cut the plastic ties securing the Upright TV Cable (104) to the left Upright (84). Connect the Upright TV Cable to the TV cable on the console assembly. 4. Insert the Console Wire Harness (78) and the TV cable into the Uprights (84). Set the console assembly on the Uprights (84). Be careful to avoid pinching the Console Wire Harness (78) and the TV cable. While a second person holds the console assembly, attach it with four Console Bolts (64) and four Star Washers (8) as shown; start all four Console Bolts and then firmly tighten them. Console Assembly 64 78 64 8 8 TV Cable 84 84 4 84 77 78 2 Console Assembly 77 78 84 104 TV Cable Console Assembly 3 8 5. Press the Latch Housing (73) into the left Upright (84). Use a rubber mallet, if necessary, to fully insert the Latch Housing. Remove the knob from the pin. Make sure that the collar and the spring are on the pin. (Note: If there are two collars, place one on each side of the spring.) Next, insert the pin into the Latch Housing (73). Then, tighten the knob back onto the pin. Plug in the power cord as described on page 12, and turn on the power as described on page 14. Note: The treadmill may automatically rise to the maximum incline level and then return to the minimum level. 6. Place the treadmill in the storage position (see HOW TO FOLD AND MOVE THE TREADMILL on page 24). Next, place the cylinder end of the Gas Spring (92) near the bracket on the base of the Uprights (84). See the two small inset drawings. Using your fingernail or the end of a screwdriver, press on the end of the Spring Pin (25) to loosen it from the Gas Spring (92). Next, rotate the Spring Pin and pull it out of the Gas Spring. Be careful to avoid losing the Spring Pin. Note: Extra Spring Pins are included. See drawing 5a. Press the cylinder end of the Gas Spring (92) onto the ball on the bracket. Next, insert the end of the Spring Pin (25) into two of the small holes in the end of the Gas Spring. Then, rotate the Spring Pin until it clips onto the Gas Spring. 7. Raise the Gas Spring (92) to a vertical position. Remove the Spring Pin (25) from the raised end of the Gas Spring as described in step 6. If necessary, rotate the Gas Spring to align the end of the Gas Spring with the ball on the bracket on the Frame (58). Next, press the Incline increase and decrease buttons on the console until the ball on the bracket is aligned with the end of the Gas Spring (92). Then, press the end of the Gas Spring onto the ball. Note: It may be necessary to press the end of the Gas Spring onto the ball while the Frame (58) is moving. See drawing 7a. Insert the Spring Pin (25) into the two indicated small holes in the end of the Gas Spring (92). Then, rotate the Spring Pin until it clips onto the Gas Spring. Press the Incline decrease button until the treadmill is at the lowest incline level. Then, unplug the power cord. Pin Spring Collar Knob 73 5 84 6 92 84 25 Bracket Cylinder 25 25 92 5a 25 Bracket 7 58 Bracket 25 92 92 Holes 25 7a 9 8. Note the location of the 75 ohm terminal on the treadmill. For the television to operate properly, a CATV cable must be connected to the 75 ohm terminal (see page 11). 75 Ohm Terminal 8 9. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used to adjust the walking belt (see page 27). If you purchase the optional chest pulse sensor (see page 23), follow the steps below to install the receiver included with the chest pulse sensor. 1. Make sure that the key is removed from the console and that the power cord is unplugged. Remove the indicated Screws (3) from the back of the Console Base (85). 2. Connect the wire on the receiver (A) to the indicated wire on the Console (34). Hold the receiver so the small cylinder is oriented as shown. Next, remove the tape from the back of the receiver, and press the receiver onto the Console Base (85) in the location shown. 3. Make sure that no wires are pinched. Reattach the Console (34) with the Screws (3). Discard the other wires included with the receiver. A Wire 85 Small Cylinder 3 3 3 3 34 10 Before operating the television, you must connect a 75 ohm CATV...