valutazioni - 2, GPA: 5
(
)
)
|
Facilità d'uso
• Remove the 3/4 X 1-1/2” GLIDES (24) from the paper backing and firmly apply them to all shown surfaces. • SECURELY assemble one SPRING PIN ASSEMBLY (21) to the spring pin barrel on the STACK BASE (3). See FIGURE 2. 21 STEP 3: FIGURE 3 • Insert two 2-1/2” ROUND END CAPS (19) into the ends of the ADJ. FOOT SUPPORT (2) as shown in FIGURE 3. • Insert one 1-3/4” END CAP (20) into the end of the ADJ. FOOT SUPPORT (2) as shown in FIGURE 3. • Attach four 3/4 X 1-1/2” GLIDES (24) to the outside of the ADJ FOOT SUPPORT (2) as shown in FIGURE 3 using the following steps: • Thoroughly clean all surfaces where the 3/4 X 1-1/2” GLIDES (24) are to be attached. • Remove the 3/4 X 1-1/2” GLIDES (24) from the paper backing and firmly apply them to all shown surfaces. • Apply two 2-1/2 X 5-1/2” NON-SKID STRIPS (18) to the ADJ. FOOT SUPPORT (2) as shown in FIGURE 3. 16 24 3 5 2 20 24 19 18 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 6 FIGURE 4 STEP 4: • SECURELY assemble the STACK BASE (3) and the UPRIGHT (1) to the LOWER CROSS SUPPORT using two 3/8 X 4” BOLTS (38), four 3/8” WASHERS (30), and two 3/8” LOW HEIGHT LOCK NUTS (29). See FIGURE 4. 3/8 X 4” 38 29 1 LOWER CROSS SUPPORT 3 UPRIGHT FRAME 30 30 • NOTE: It may be necessary to loosen the 1/2 X 3-1/4” BOLTS of the LOWER CROSS SUPPORT connecting to the UPRIGHT FRAME before beginning STEP 4. 3/8” LOW HEIGHT LOCK NUT 2 21 • Pull back on the SPRING PIN (21) and CAREFULLY insert the ADJ. FOOT SUPPORT (2) into the STACK BASE (3) as shown in FIGURE 4. STEP 5: FIGURE 5 • Snap two WEIGHT PLATE BUSHINGS (28) into the top of all twenty WEIGHT PLATES (40) as shown in FIGURE 5. 39 • Retighten the 1/2 X 3-1/4” BOLTS loosened in the above STEP. • Slide the WEIGHT PLATE SHAFT (39) thru the hole in the HEAD PLATE (36) and lock in place using one 3/4” E-RING (25) as shown in FIGURE 5 40 28 25 36 7 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 6 STEP 6: • Insert two GUIDE RODS (6) into the STACK BASE (3) as shown in FIGURE 6. Lubricate the GUIDE RODS (6) with a silicon or teflon spray that is available at most hardware stores. • Slide two WEIGHT STACK CUSHIONS (26) down over the GUIDE RODS (6). See FIGURE 6. • Using EXTREME CARE slide twenty WEIGHT PLATES (40) down over the GUIDE RODS (6) with the key-hole facing as shown in FIGURE 6. • Apply one set of WEIGHT STACK LABELS - 1-26 (41) to each WEIGHT PLATE (40) as shown in FIGURE 6. • Slide two 13/16” SHAFT COLLARS (15) over the GUIDE RODS (6) as shown in FIGURE 6. 6 40 26 3 41 15 • Carefully Slide the HEAD PLATE ASSEMBLY (39 & 40) down over the GUIDE RODS (6) onto the weight stack as shown in FIGURE 6. HEAD PLATE ASSEMBLY 8 STEP 7: FIGURE 7 • LOOSELY assemble the TOP BOOM (4) to the UPPER CROSS SUPPORT using two 3/8 X 4” BOLTS (38), four 3/8” WASHERS (30) and two 3/8” LOCK NUTS (31). See FIGURE 7. • Insert two 3 X 2” END CAPS (13) into the ends of the TOP BOOM (4). See FIGURE 7. • SECURELY tighten all connections made up to this point. 38 3/8 X 4” 32 3/8 X 2-3/4” 4 27 30 30 13 UPRIGHT UPPER CROSS SUPPORT • NOTE: It may be necessary to loosen the 1/2 X 3-1/4” BOLTS of the UPPER CROSS SUPPORT connecting the UPRIGHT FRAME before beginning STEP 7. • Slide the 13/16” SHAFT COLLARS (15) to the top of the GUIDE RODS (6) and SECURELY tighten the SHAFT COLLAR (15) set screws. See FIGURE 7. 15 31 31 • Place TOP BOOM (4) over the GUIDE RODS (6) and LOOSELY assemble the TOP BOOM (4) to the UPRIGHT (1) using one 3/8 X 2- 3/4” BOLT (32) and one 3/8” LOCK NUT (31) as shown in FIGURE 7 • Insert two GUIDE ROD BUSHINGS (27) into the TOP BOOM (4) as shown in FIGURE 7. 16 13 1 6 • Insert two 2” SQ. END CAPS (16) into the ends of the TOP BOOM (4). See FIGURE 7. 9 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 9: FIGURE 9 • Route the 115-3/4” CABLE (12) through the TOP BOOM (4) as shown in FIGURE 9. (NOTE: It may be necessary to remove the 3/8 X 2-3/4” BOLT to ensure CABLE is routed over the TOP of the BOLT.) • SECURELY assemble three 3-1/2” PULLEYS (9) into the slots of the TOP BOOM (4) using three 3/8 X 2-3/4” BOLTS (32), six 3/8” FLANGE SPACERS (33), and three 3/8” LOCK NUTS (31) as shown in FIGURE 9. (NOTE: Make sure the cable is routed over all the pulleys.) 9 3/8 X 2-3/4” 32 4 12 33 31 STEP 8: FIGURE 8 • Slide two VINYL CAPS (22) over the LAT BAR SUPPORT (5) as shown in FIGURE 8. • SECURELY assemble the LAT BAR SUPPORT (5) to the TOP BOOM (4) using one 3/8 X 2-3/4” (32) and one 3/8” LOW HEIGHT LOCK NUT (29). See FIGURE 8. 32 3/8 X 2-3/4 3/8” LOW HEIGHT 29 22 4 5 Make sure CABLE is routed over bolt! • SECURELY retighten the removed 3/8 X 2-3/4” BOLT from the above step. STEP 10: FIGURE 10 10 31 • Place one 3-1/2” PULLEY (9) into the loop of the CABLE (12) below the second and third PULLEY of the TOP BOOM (4) as shown in FIGURE 10. • LOOSELY assemble two 3/16 X 1-3/4 X 5-1/4” PLATES (23) to each side of the 3-1/2” PULLEY (9) using one 3/8 X 2” BOLT (35), two 3/8” WASHERS (30), and one 3/8” LOCK NUT (31). See FIGURE 10. !IMPORTANT! SECURELY TIGHTEN JAM NUT 35 3/8 X 2” 4...