Log:
valutazioni - 2, GPA: 4 ( )

Istruzioni per l'uso Life Fitness, Modello CL5X

Produttore : Life Fitness
File Size : 5.43 mb
File Nome : 603d3fac-02a6-4ae1-a55e-4c6d42c58fcb.pdf
Lingua di insegnamento: enesfr
Vai a scaricare



Facilità d'uso


Route the POWER CABLE and COAXIAL CABLE alongside the MAIN WIRE HARNESS where applicable. 6 1. Before proceeding, familiarize yourself with the parts of the Cross-Trainer and make sure that you have received all the items described in the Parts List. 2. Locate the left and right FRONT COVER (#9, #10). Using two PHILLIPS PAN HEAD SCREWS (#3), mount the USER LEFT FRONT COVER (#9) to the FRAME (A). Attach the USER RIGHT FRONT COVER (#10) to the FRAME in the same manner using two PHILLIPS PAN HEAD SCREWS (#3). Secure the tops of the FRONT COVERS together using two PHILLIPS PAN HEAD SCREWS (#3). CAUTION: Do not overtighten the PHILLIPS PAN HEAD SCREWS (#3). 3. Locate the RIGHT USER ARM (#12). Snap the 2-PIN CONNECTOR (2PA) located at the bottom of the RIGHT USER ARM into the 2-PIN CONNECTOR (2PB) positioned at the top of the RIGHT ROCKER ARM (B). Feed the connectors and excess cable up into the RIGHT USER ARM. Secure the RIGHT USER ARM to the RIGHT ROCKER ARM using three HEX SOCKET HEAD CAP SCREWS (#1) and INTERNAL TOOTH LOCK WASHERS (#18). Repeat the procedure for the LEFT USER ARM (#11) and LEFT rocker arm (C). Tighten all screws securely. CAUTION: Be careful not to pinch the WIRE HARNESSES when assembling the USER ARMS (#11 & #12) to the ROCKER ARMS (B & C). 4. Detach and unwrap the WIRE HARNESS (E) (16P, 4P) located at the top of the MONOCOLUMN (F). Holding the CONSOLE SUPPORT ASSEMBLY (#7) with the handgrips facing upward, feed the WIRE HARNESS up through the neck and out the top access hole. Carefully lower the CONSOLE SUPPORT ASSEMBLY into the MONOCOLUMN. CAUTION: Be careful not to pinch the WIRE HARNESSES (E) when assembling the CONSOLE SUPPORT ASSEMBLY (#7) to the MONOCOLUMN (F). 5. Using two HEX SOCKET HEAD CAP SCREWS (#1) and two FLAT WASHERS (#8), secure the CONSOLE SUPPORT ASSEMBLY (#7) to the MONOCOLUMN (F). Tighten the SCREWS securely. 6. Locate the ACCESSORY TRAY (#17). Align the ACCESSORY TRAY with the bottom of the DISPLAY CONSOLE (#4) as shown. Using four MOUNTING SCREWS (#2), secure the ACCESSORY TRAY to the DISPLAY CONSOLE as shown. Tighten the SCREWS securely. CAUTION: Do not overtighten the MOUNTING SCREWS (#2). 7 7. Attach the 4-PIN (4P), 3-PIN (3P), and 16-PIN (16P) CONNECTORS to the corresponding JACKS on the back of the CONSOLE ASSEMBLY (#4). 8. Feed any excess WIRE HARNESS (E) down into the CONSOLE SUPPORT ASSEMBLY (#7). Secure the CONSOLE ASSEMBLY (#4) to the CONSOLE SUPPORT ASSEMBLY using four PHILLIPS PAN HEAD SCREWS (#2). Tighten the SCREWS securely. CAUTION: Do not over-tighten the PHILLIPS HEAD PAN SCREWS (#2). CAUTION: Be careful not to pinch the WIRE HARNESS (E) when assembling the CONSOLE ASSEMBLY (#4) to the CONSOLE SUPPORT ASSEMBLY (#7). 9. Locate and install the CONSOLE SUPPORT CAP (#19) onto the CONSOLE SUPPORT ASSEMBLY (#7) as shown. 10. Locate the POLAR RECEIVER (#16). Slide the FOAM ISOLATOR (#15) over the POLAR RECEIVER. Remove the POLAR RECEIVER JACK (G) from the tape and plug the POLAR RECEIVER into the POLAR RECEIVER JACK. 11. Locate the FRONT and BACK MONOCOLUMN COVERS (#5 & #6). With the WIRE positioned on top, carefully insert the POLAR RECEIVER (#16) between the vertical ribs located inside the BACK MONOCOLUMN COVER (#6). Place the BACK MONOCOLUMN COVER (#6) over the PIVOT SHAFT (H) at the top of the MONOCOLUMN (F). NOTE: The POLAR RECEIVER WIRE must be positioned on top when inserted into the REAR MONOCOLUMN COVER (#6). 12. Place the FRONT MONOCOLUMN COVER (#5) on the opposite side of the BACK MONOCOLUMN COVER (#6) to cover the PIVOT SHAFT (G) and CONSOLE SUPPORT ASSEMBLY MOUNTING SCREWS. Interlock the top tabs and use two PHILLIPS PAN HEAD SCREWS (#3) to secure the bottoms of the MONOCOLUMN COVERS together. Tighten the SCREWS securely. CAUTION: Do not over-tighten the PHILLIPS PAN HEAD SCREWS (#3). 13. Locate one FRONT ROCKER COVER (#13) and one BACK ROCKER COVER (#14). Position the FRONT ROCKER COVER over the user side of the left end of the PIVOT SHAFT (H) (as shown) making sure that it interlocks with the MONOCOLUMN COVERS (#5 & #6). Place the BACK ROCKER COVER over the opposite side of the left end of the PIVOT SHAFT in the same manner. Secure the COVERS using three PHILLIPS PAN HEAD SCREWS (#3). Repeat the procedure reversing front and back for the user right end of the PIVOT SHAFT. CAUTION: Do not over-tighten the PHILLIPS PAN HEAD SCREWS (#3). PHYSICAL DIMENSIONS: Length: 83 inches / 211 centimeters Width: 28 inches / 71 centimeters Height: 61 inches / 155 centimeters Weight: 235 pounds / 106.5 kilograms PRE-OPERATION CHECKLIST • Ensure that all fasteners are tight. • Make sure the CROSS-TRAINER is properly leveled and stable. (Refer to the Operation Manual) • Ensure that the Leveler Jam Nuts are tight. (Refer to the Operation Manual) • Read the entire Operation manual before using the Cross-Trainer. LISTE DES VERIFICATIONS A EFFECTUER AVANT L'UTILISATION • Verifiez si tous les dispositifs de fixation sont serres. • Verifiez si le CROSS-TRAINER est de ...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie