valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Before beginning assembly, read the instructions and identify parts using the hardware identifier and parts list in this document. For more information on assembly, maintenance, visit The American 1 © COPYRIGHT 2002 by HUFFY SPORTS 08/02 P/N 214969 ENGLISH INSTRUCTIONS IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL 1. 20. Support pole on sawhorse. Attach backboard assembly to top pole section (1). NOTE: Two people are recommended for this step, use caution, elevator 21. 22. 23. assembly is heavy. Install handle assembly to lower elevator tubes (34) using bolt (35), spacers (37), and nut (36) as shown. NOTE: Before going on to next step, adjust adjustable system assembly to the 10’ setting. Insert bolt (35) through left side upper elevator tube (33), then stretch spring (38) onto bolt (35). Insert bolt (35) through right side upper elevator tube (33) and secure with nut (36). WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS. Place re-bar (36” section - not included) into bottom pole section (3) as shown. Secure pole end with tape (not included) to retain re-bar inside the bottom pole section (3). NOTE: Make sure that concrete does not bulge from the end of pole assembly. Fill pole with concrete approximately 1” (2.54 cm) below bottom hole as shown. Allow concrete to completely cure. IMPORTANT! Failure to fill your pole completely with concrete as described in these instructions will void all warranties written and implied. NOTE: Maximum distance from edge of hole to edge of playing surface 6” (15.2 cm). IMPORTANT! Wait minimum of 24 hours before going on to next step. Concrete must cure. WARNING: THIS HOLE SIZE REPRESENTS THE MINIMUM REQUIREMENT 24. Remove tape, install pole cap (45), fit pole assembly into sleeve (4). FOR IDEAL CONDITIONS. THE LOCATION (HILL/INCLINE) OF THE POLE, IMPORTANT! Position pole section so the elevator assembly is SOIL CONDITIONS (SAND/CLAY) AND OTHER FACTORS COULD REQUIRE A perpendicular with playing surface. LARGER HOLE SIZE AND CONCRETE FOOTING. 3. Insert and secure bottom pole section (3) into ground sleeve (4). WARNING: TWO PEOPLE ARE RECOMMENDED FOR THIS STEP. POLE 4. Fill hole approximately 1/3 full with concrete. Insert ground sleeve assembly and FILLED WITH CONCRETE WEIGHS APPROXIMATELY 125 LBS. (56.7 KG). center in hole. Fill hole completely with concrete. USE PROPER PRECAUTION. NOTE: Make sure that bottom of ground sleeve flange is level with playing IMPORTANT! The elevator holes MUST be parallel with playing surface. surface. 25. Use wedge to tap cap of ground sleeve until tight. 5. Tamp down concrete to release air pockets and build drainage hill. Level pole 26. Install rim (40) to backboard as shown. NOTE: Mounting nuts and bolts supplied section in all directions several times while concrete is curing. with rim hardware. NOTE A: Mark here for tape. WARNING: TWO PEOPLE ARE NECESSARY TO MOUNT BACKBOARD NOTE B: Keep flange pushed down to concrete and leveled. ASSEMBLY TO THE POLE. ONE PERSON SHOULD NOT ATTEMPT TO DO IMPORTANT! Wait minimum of 24 hours before going on to next step. THIS ALONE. Concrete must cure. 6. After concrete has cured, remove bottom pole section from ground sleeve (4). WARNING: MOUNTING THE BACKBOARD ASSEMBLY TO THE POLE IS Place anti-skid tape (6) around bottom of pole. PERFORMED AT AN ELEVATED HEIGHT. USE PROPER PRECAUTION. NOTE A: Place top edge of tape on mark. 27. Apply height adjustment label (45) to front of pole as shown. NOTE B: Tape prevents the pole from rotating during play. 28. Grasp handle and depress lever. 7. Install ground sleeve cap (5) onto bottom pole section. Stack and bounce bottom WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT. and middle pole sections together. Bounce pole sections together until middle 29. Push toward pole while holding lever. Raise or lower lever to desired height while section no longer moves toward taped reference mark. pushing forward on handle. 8. Stack upper pole section (1) to bottom pole assembly and continue bouncing until 30. Release handle making sure that horizontal pin (21) is locked into slot. poles no longer move toward taped reference marks. IMPORTANT! Pole sections should have a 3-3/4” (9.5 CM) minimum overlap. WARNING: USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF 9. Snap tinnerman nut (7) onto inner channel (8). Place inner channel into outer SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD channel (9) as shown. RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS and nuts (13). Tighten completely. CAREFULLY. 10. Slide handle (10) into position as shown and secure with bolts (11), washers (12), 11. Install bolt (14), washers (12), and nut (15) as shown. NOTE: Tighten until washers (12) are no longer loose. Assemble trigger (16) to 31. Install net clips as shown. (See illustration) handle assembly as shown and secure with bolt (17) and washer (12). Tighten completely. 32. Install net as shown. (See illustration) 12. Ins...