valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
4 201124 Lock Nut, Hex Head, 3/8-16 4 206360 Bolt, Hex Head, 3/8-16 x 2-5/8 Long 2 204858 Spacer, Biscuit, Plastic 2 204857 Spacer, Metal 1/2” O.D.x1.44 Long 2 204859 Cover, Spring 1 203038 Carriage Bolt, 5/16-18 x 2-3/4 Long 1 204850 Pin, Locking 1 204853 Lanyard, Black Coil 1 904833 Height Adjustment Rod 1 204872 Label, Height Indicator 2 203103 Carriage Bolt, 5/16-18 x 2 Long 31 1 204803 Screw, Phillips Head Item Qty. Part No. Description 32 1 204855 Handle, Left 33 1 204856 Handle, Right 34 2 900103 Board Bracket 35 4 201683 Spacer .530 I.D. x.63 O.D. x 1.50 Long 36 2 200874 Spacer, Steel .402 I.D.x50 O.D.x1.5 L 37 1 206990 Reinforcement Bracket 38 4 201681 Spacer, Plastic, .530 I.D. x .875 Long 39 7 206340 Lock Nut, Hex Head, 1/2-13 40 2 904820 Elevator Tube, Lower - Long 41 1 204837 Spring 42 1 Rim 43 2 904808 Elevator Tube, Upper - Short 44 2 201682 Spacer, .530 I.D. x 1.875 Long 45 2 900867 Plate, Triangle, (Black) 46 1 202814 Cap, Pole Top 47 6 206244 Bolt, Hex, 1/2-13 x 8 Long 48 1 204870 Bolt, Hex, 1/2-13 x 3-1/2 Long 49 2 203617 Plug Cap 50 12 201219 Smart Clip, Net Holder 51 1 Net 52 1 201568 Anchor, T-strap 53 1 203124 Stake, Tie Down 54 1 201252 Label, Height Adjustment and Moving 55 4* 205528 Bolt, Hex Flange, 5/16-18 x 1 Long * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. HARDWARE IDENTIFIER (NUTS & WASHERS, STEEL RODS & STEEL SPACERS) Item #2 (2) Item #12 (1) Item #13 (7) Item #16 (9)* Item #19 (4) Item #20 (4) Item #23 (2) Item #9 (1) Item #7 (1) Item #36 (2) Item #39 (7) Item #10 (1) 7 01/04 P/N 214954E HARDWARE IDENTIFIER (BOLTS & SCREWS) * You may have extra parts with this model. Item #14 (1) Item #18 (2) Item #21 (4) Item #22 (2) Item #25 (1) Item #30 (2) Item #31 (1) Item #38 (4) Item #35 (4) Item #48 (1) Item #55 (4)* Item #47 (6) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #50 (12) Item #8 (1) Item #15 (2) Item #44 (2) 8 P/N 214954E 01/04 Remove all contents from underside of tank. Keep tank (1) bottom side up 1. 1. 1 Insert axle rod (2) through wheel (3), as shown. Secure wheel assembly to tank (1) by tapping wheel downward with hammer, snapping it into position. Repeat for opposite side, then carefully, turn tank (1) over. 3 2 2. 1 4 5 Mark pole sections with tape as shown. TAPE (not included) 3. 6 9 01/04 P/N 214954E 5 4 IMPORTANT! Center alignment slot of middle pole section (5) in a lower hole of top pole section (4) as shown. While maintaining alignment, bounce middle pole (5) into top pole section (4) as shown until top pole section no longer moves toward taped reference mark on middle pole. Upright assembly. WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 4. 5 4 IMPORTANT! Center alignment slot of middle pole section (5) in a lower hole of top pole section (4) as shown. While maintaining alignment, bounce middle pole (5) into top pole section (4) as shown until top pole section no longer moves toward taped reference mark on middle pole. Upright assembly. WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 4. IMPORTANT! Center alignment slot of lower pole section (6) in a lower hole of middle pole section (5) as in step 3. While maintaining alignment, bounce top & middle pole assembly (4 & 5) onto lower pole section (6) as shown until top & middle pole assembly no longer moves toward taped reference mark on bottom pole. 4 5 6 WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 5. 10 P/N 214954E 01/04 6. 6. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 7 4 8 6 5 Insert pole assembly into tank assembly as shown. 7. 6 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. IMPORTANT!: DO NOT OVER TIGHTEN 7 8 8. 8. Carefully place unit on its side. Secure pole bottom (6) to tank with anchor strap (52), washers (9 & 13) and nut (10) as shown. Upright unit. NOTE: 6 Keep unnecessary pressure off of the pole assembly when in this position. Two people recommended for this procedure. 1 9 13 10 52 IMPORTANT!: DO NOT OVER TIGHTEN 11 01/04 P/N 214954E 1 11 11 12 13 6 14 13 Secure strut tubes (11) to bottom pole section (6) as shown. TIGHTEN BOLT (14) IN LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. WARNING! 9. 1 11 11 12 13 6 14 13 Secure strut tubes (11) to bottom pole section (6) as shown. TIGHTEN BOLT (14) IN LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. WARNING! 9. 10. Carefully place unit in the side position and secure strut (11) to tank (1) as shown. Completely tighten. Repeat for opposite side. Upright unit. 12P/N 214954E 01/04 15 16 11 1 13 13 Keep unnecessary pressure off of the pole assembly when in this position. Two people recommended for this procedure. NOTE: 1 Install pole mount bracket (17) and reinforcement bracket (37) with carriage 11. bolts (18) as shown. Tighten flange nuts (16) completely. 4 16 37 18 18 16 1...