valutazioni - 3, GPA: 4
(
)
)
|
Foto e specifiche Vision Fitness R2850HRT |
Facilità d'uso
Box 280 • Lake Mills. WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 ©2007 Vision Fitness. All Rights Reserved. 5.07 AG18.44PRD REV4 TOOLS & PARTS INCLUDED HARDWARE INCLUDED HARDWARE INCLUDED 15mm Pedal Wrench 5mm T-Shaped Wrench 4mm L-Shaped Wrench Screwdriver 6mm L-Shaped Wrench PARTS BOX ORANGE BAG BLUE BAG M8 x 15L Bolt Quantity: 6 M8 x 20L Bolt Quantity: 2 M8 x 65L Bolt Quantity: 2 M8 Lock Washer Quantity: 4 M10 x 12L Set Screw Quantity: 1 BLACK BAG M6 x 55L Bolt Quantity: 4 M6 Lock Washer Quantity: 8 YELLOW BAG M5 x 35L Bolt Quantity: 2 M5 Lock Washer Quantity: 2 GREEN BAG Seat Rail Stopper w/Axle illustration not to scale Quantity: 1 Seat Rail Stopper illustration not to scale Quantity: 1 M5 x 16 Flat Washer Quantity: 1 M5 x 8L Bolt Quantity: 4 M4 x 10L Bolt Quantity: 1 M8 Lock Washer Quantity: 4 M8 x 20L Socket Head Cap Bolt Quantity: 4 M6 x 15L Bolt Quantity: 4 M8 x 15L Bolt Quantity: 4 PINK BAG Console Mast Cover Accessory Tray Color-coded Hardware Bags Pedals/Straps Owner’s Guide Assembly Guide Warranty Card 5mm L-Shaped Wrench STEP 2 • Slide the console mast boot onto the console mast. • Unfold the wire harness, heart rate wires, coaxial cable, and TV power cable located in the console mast frame bracket. Attach the wire tie coming from the bottom of the console mast to the cables and wires. Pull the wire tie with cables and wires up through the top of the console mast while simultaneously sliding the mast into the frame bracket. • Secure the console mast to the frame bracket with six bolts (M8x15L). Tighten with the 5mm T-Shaped wrench. Insert a set screw (M10x12L) to the front edge of the mast and tighten until snug with the 5mm T-shaped wrench. • Slide the console mast boot down and snap it into place on the side cover. BLUE BAG STEP 3 • Mount the upper handlebars to the console mast using four bolts (M8x15L). Tighten with the 5mm T-Shaped wrench. • Tuck the coaxial and TV power cables into the console mast. NOTE: If you have purchased the TV bracket assembly, remove the screws from the TV bracket cover located at the front of the console mast and remove the cover. Feed the coaxial and TV power cables through the hole at the front of the console mast. • Remove the four mounting bolts from the back of the console. Connect the wire harnesses and heart rate wires that come from the console mast into the plugs located in the back of the console. Attach the console to the mast with the four bolts removed earlier. PINK BAG STEP 1 • Install the rear foot with the four lock washers (M8), two inside bolts (M8x65L), and two outside bolts (M8x20L). Tighten with the 5mm T-Shaped wrench. ORANGE BAG A s s e m b l y G u i d e R2850HRT COMMERCIAL FITNESS BIKE STEP 1 STEP 4 • Remove the two socket head cap bolts from the bracket for the seat rail adjustment lever. Slide the seat rail adjustment handle between the teeth of the seat adjustment bracket. Re-insert socket head cap bolts and tighten with the 4mm L-shaped wrench. • Slide the seat frame on to the back end of the seat rail. • Slide the axle with the seat rail stopper through the hole in the back side of the seat rail. Set the opposite side seat rail stopper in place and attach with a washer (M5x16) and bolt (M4x10L). Tighten with the screwdriver. • Slide the seat rail end cap into place on the back side of the seat rail. Fix in place with two bolts (M5x8L) at the rear of the seat rail and two bolts (M5x8L) to the side covers. Tighten with the screwdriver. GREEN BAG STEP 2 To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike. If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw. STEP 5 STEP 4 STEP 5 • There will be a wire tie that is connected to the front end of the seat frame. Take this wire tie and wrap around the end of the wire harness coming from the seat rail. Simultaneously slide the seat frame forward and pull the wire tie with wire harness up through the hole in the middle of the seat frame. Insert a zip tie through the hole in the frame and loop it around the wire harness about one inch from the end. Pull the zip tie snug, but not over tight. • Connect the wire harness from the seat handlebar to the wire harness coming from the seat frame. Slide the connectors and excess wire into the hole in the seat frame. • Mount...