valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
A high probability of serious injury exists if this system is not installed, maintained, and operated properly. • If using a ladder during assembly, use extreme caution. • Check base regularly for leakage. Slow leaks could cause the system to tip over unexpectedly • Seat the pole sections properly (if applicable). Failure to do so could allow the pole sections to separate during play and/or during transport of the system. • Climate, corrosion or misuse could result in system failure. • If technical assistance is required, contact Customer Service. • Minimum operational height is 4'-6" (1.37m) to the bottom of backboard. Most injuries are caused by misuse and/or not following instructions. Use caution when using this unit. NOTICE TO ASSEMBLERS Adult Assembly Required. Dispose of ALL packaging materials promptly. As with all children’s products, periodically inspect for loose small parts. Assembled unit MUST be filled with water at ALL times. ALL basketball systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. PRODUCT REGISTRATION: Please remember to complete your product registration form online at: 3 01/07 ID# M5800142 ID# M5800142 01/07 4 Get to know the basic parts of your basketball system... FRONT TOP POLE BACK MIDDLE POLE RIM BOTTOM POLE STRUTS ELEVATOR ASSEMBLY BACKBOARD BASE PARTS LIST Item Qty. Part No. Description 1 1 20664903 Tank (Black) 2 1 90813001 Top Pole Section 3 1 90813301 Middle Pole Section with Label 4 1 908132 Bottom Pole Section 5 1 203099 Nut, Ny-Lock, 5/16-18 6 1 Net 7 1 20378701 Cap, Pole 8 3 203223 Bolt, Carriage, 5/16-18 x 1" Long 9 1 203617 Cap, Tank 10 1 203740 Bolt, Hex, 5/16-18 x 2.63" Long 11 2 600088 Knob, Plastic, 3-sided 12 1 Rim 13 1 Backboard 14 1 90813401 Backboard Mounting Bracket 15 1 908129 Rim Bracket 16 2 206686 Bolt, Carriage 1/4-20 x 3.25" Long 17 4* 203218 Washer, Flat, 5/16 18 1 203309 Washer, Flat, 1.0" O.D. 19 1 203679 Bolt, Hex, 3/8-16 x 2" Long 20 3* 203100 Nut, Flange, 5/16-18 21 1 900454 Strut, Left 22 1 900255 Strut, Right 23 1 558170 Label, Height Adjustment * You may have extra parts with this model. 5 01/07 ID# M5800142 PARTS IDENTIFIER - Actual Size #8 (3) #10 (1) #16 (2) #19 (1) #5 (1) #17 (4*) #18 (1) #20 (3*) PARTS IDENTIFIER - Not Actual Size #1 (1) #11 (2) #13 (1) #12 (1)#14 (1) #21 (1) #22 (1) #15 (1) #9 (1) #6 (1) #7 (1) ID# M5800142 01/07 6 SECTION A: ASSEMBLE THE POLES 1. Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. 3 2 4 TOP MIDDLE BOTTOM Reference Stickers 7 01/07 ID# M5800142 IMPORTANT! ONCE POLE SECTIONS ARE POUNDED TOGETHER - THEY CANNOT BE TAKEN APART 2. 3 2 4 TOP MIDDLE BOTTOM alignment mark alignment mark alignment mark Align poles using alignment marks. First, pound top and middle poles together by bouncing them on a scrap piece of wood on the ground as shown in FIG A. until they no longer move toward pole identification stickers. THEN add bottom pole section and pound together in the same way. FIG A. scrap wood (Not Supplied) middle pole IDENTIFICATION STICKER middle pole IDENTIFICATION STICKER 3-1/2” 1-1/4" THE IDENTIFICATION STICKER IS LOCATED 3-3/4" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 2-1/2" MINIMUM OVERLAP, LEAVING 1-1/4" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. CAUTION! ID# M5800142 01/07 8 9 01/07 ID# M5800142 Attach pole assembly to tank as shown. Secure pole assembly to tank by turning the 3. pole assembly clockwise as shown. 18 19 CAREFULLY TIPPING THE 4 SYSTEM FORWARD WILL ALLOW EASIER ACCESS TO UNDERSIDE OF BASE NOTE: IMPORTANT! NOTE ORIENTATION. TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! ID# M5800142 01/07 10 5. Rotate struts down and bend struts outward to line up with holes on base as shown. Secure free ends of tank struts to tank with carriage bolt (8), and nut (20) as shown. Repeat for other side. 17 22 1 17 21 5 10 Secure tank struts (21 & 22) to pole. TIGHTEN BOLT (10) IN LOCK NUT (5) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 4. 8 20 17 8 20 17 6. Pole bracket will need to be lightly pressed into backboard ribbing. Be sure to press completely into place. Attach rim to backboard and pole bracket (14) with nut (20), reinforcement bracket (15), and carriage bolt (8) as shown. Tighten nut completely. Press bracket (14) into place here. 8 15 14 12 13 20 Carefully tip unit forward and slide ba...