valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
11. Secure both hinge tubes (24) to second wheel bracket (25) with carriage bolts (26) and flange nuts (15). 12. Install wheels (27) onto axle (28) and wheel bracket (25) with push caps (29) as shown. 13. Position base as shown. Secure wheel bracket assembly with disc (30), washer (20) and nut (8) as shown. NOTE: Two people recommended for this step. 14. Carefully reposition entire assembly as shown. IMPORTANT! Two people recommended for this step. 15. Snap tinnerman nut (31) onto inner channel (32). Place inner channel into outer channel (33) as shown. 16. Slide handle (34) into position as shown and secure with bolts (35), washers (11), and nuts (15). Tighten completely. 17. Install bolt (36), washers (11), and nut (37) as shown. Tighten until washers (11) are no longer loose. NOTE: Do not over tighten. Assemble trigger (38) to handle assembly (34, 32, 31) as shown and secure with bolt (39) and washer (11). Tighten completely. 18. WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS. Install trigger return spring (40) to handle assembly (32, 33) as shown. 19. Attach Accuheight label (41) to inner channel (32). 20. Attach spring (44) to pins (43) and install pins (43) onto pole mount bracket (45). Attach other spring (44) to opposite side. NOTE: Gently enlarge eyelets of spring with pliers if springs do not fit over pins. WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS. 21. Install pole mount assembly and reinforcement bracket (47) with carriage bolts (46) to pole as shown. Tighten flange nuts (15) completely. 22. Push back sliding pin (43) as shown in Figure A to fit adjustable system assembly through pole mount assembly. Then attach spring covers (48 & 49) onto pole mount bracket (45) with bolt (50), and nut (15) as shown in Figure B. 23. Install spacers (51) onto backboard brackets (52) with bolts (53, 54) and lock nuts (55, 37) as shown. 24. Assemble lower elevator tubes (56) as shown. NOTE: Tighten bolt (57) in lock nut (58) until flush (even) with lock nut’s outer edge. IMPORTANT! It is necessary for all parts to be installed for this mechanism to work safely and properly. NOTE: Test fit bolts into holes of brackets (52) and carefully rock them in a circular motion to ream out paint from holes if necessary 25. Place board spacers (75) into board as shown. Bend brackets (52) to line up with holes in board. Insert bolts (62) into holes as shown. Tighten completely. NOTE: Rim mounting nuts (15) and bolts (60) supplied with rim hardware. 26. Assemble upper elevator tubes (63) to backboard brackets (52) as shown. NOTE: Tighten bolt (57) in lock nut (58) until flush (even) with lock nut’s outer edge. 27. Support pole on sawhorse. Attach backboard assembly to top pole section (1) as shown. Then install pole cap (64). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy. 28. Install upper elevator tubes (63) to triangle plates (66) as shown. Next, Install handle assembly (32, 33) to lower elevator tubes (56) using bolt (57), spacers (67), and nut (58) as shown. NOTE: Tighten bolt (57) in lock nut (58) until flush (even) with lock nut’s outer edge. NOTE: Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. 29. WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS. Insert bolt (57) through left side upper elevator tube (63), then stretch spring (68) onto bolt (57). Insert bolt (57) through right side upper elevator tube (63) and secure with nut (58). 30. Attach front cover (72) to hinge tubes (24) using carriage bolt (61) and flange nuts (15) as shown. WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY, MAY TIP OVER. 31. Apply height and moving label (73) to front of pole as shown. 32. Roll completed assembly to desired playing area. Secure assembly to ground using strap (74) and tie down stake (7). Fill tank with 34 gallons of water. IMPORTANT! Add two gallons (7.6 Liters) of non-toxic antifreeze in sub-freezing climates. Add two gallons (7.6 liters) to tank to prevent freezing in sub-freezing climates. Snap cap (42) into place. 33. WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT. Grasp handle and depress lever. 34. Push toward pole while holding lever. Raise or lower lever to desired height while pushing forward on handle. 35. Release handle making sure that horizontal pin (43) is locked into slot. WARNING: USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. 36. Install net clips as shown. (See illustration) 37. Install net as shown. (See illustration) 5 04/03 P/N 214973A IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL 1. 5" (13 cm) MIDDLE TOP 5" (13 cm) BOTTOM 1 3 2 2. 1 2 Note (See Text Page) IMPORTANT! (See Text Page) Wood Scrap Note (See Text Page) IMPORTANT! (See Text Page) 2 3 1 3. P/N 214973A 04/03 6 4. 25 17 17 29 28 IMPORTANT!: 25 17 17 29 28 IMPORTANT!: 5. 16 16 29 SIDE OF WHEEL WI...