TOWARDS BOARD TOWARDS POLE 1. 1. Assemble backboard brackets (27) using bolts (52), and nuts (11) as shown. 27 52 11 11 52 27 29 NOTE ORIENTATION 21 06/06 ID# M6611341 ID# M6611341 06/06 22 Support pole on sawhorse. Attach triangle plates (37) and elevator tubes (35 & 32) to top pole (4) using bolts (40 & 29) and nuts (31). Install pole cap (38). 2. 35 31 29 35 31 31 30 30 40 37 37 32 32 4 COMPLETED ASSEMBLY 38 30 USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY. TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 3. 3. Install handle assembly to lower elevator tubes (32) using bolt (29), spacers (36), and nut (31) as shown. 29 35 31 35 36 36 4 NOTE: Before going on to next step, make sure adjustable system assembly is set to the 10’ (3.05 m) setting. 23 06/06 ID# M6611341 ID# M6611341 06/06 24 4. Attach upper elevator tubes (35) to backboard support brackets (27) using spacers (26), bolt (29), and nut (31) as shown. 5. Attach lower elevator tubes (32) and counter balance spring (33) to backboard support brackets (27) using spacers (26), bolt (29), and nut (31) as shown. 29 26 26 27 31 33 32 29 32 26 31 25 06/06 ID# M6611341 6. Insert T-bolt (55) into rim bracket (54) then, attach that assembly to board using bolts (44) and nuts (14) 14 55 54 54 14 44 Insert bolt (29) through left side upper elevator tube (35), then stretch spring (33) onto bolt (29). Insert bolt (29) through right side upper elevator tube (35) and secure with nut (31). 7. 29 31 33 35 35 USE EYE PROTECTION WHEN INSTALLING SPRINGS. WARNING! ID# M6611341 06/06 26 8. 56 58 39 54 55 Install Slam Jam Rim to Backboard 34 57 55 39 58 A B C D E A Fit rim (34) securely into bracket (54) as shown. Allow T-bolt (55) to slip through center hole in rim (34). B Install reinforcement bracket (56) onto T-bolt (55) as shown. C Install spring (57) onto T-bolt (55) as shown. D Install special nut (58) and washer (39) onto T-bolt (55). E Tighten nut (58) until flush with end of T-bolt (55). 55 55 27 06/06 ID# M6611341 10. Roll completed assembly to desired position. Fill tank with water (approx. 34 gallons (129 Liters)) or sand (approx. 300 lbs. (136 kg)) and rotate the cap (41) into base (1). 41 ADD TWO GALLONS (7.6 LITERS) OF NON-TOXIC ANTIFREEZE IN SUBFREEZING CLIMATES. CAUTION! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! IF USING SAND: 2 GALLONS OF ANTI-FREEZE IS NOT REQUIRED NOTE: SANDSAND (300 lb.)(lb.) (136 kg)(kg) 1 9. Install net (43). 1. 2. 3. 4. ID# M6611341 06/06 28 1. Apply height adjustment and moving label (46) to front of pole as shown. 2. A. While holding handle, remove pin (24). B. Move elevator up or down to desired height. C. Replace pin (24) full length to lock system at desired height. SECTION C: APPLY HEIGHT AND MOVING LABEL & HEIGHT ADJUSTMENT 10 ft. 46 (3.05 m) 24 A. B. C. TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! DO NOT ALLOW CHILDREN TO ADJUST HEIGHT. WARNING! Peel protective film from surface of acrylic backboard prior to use. NOTE: SECTION D: BOARD PAD 63 63 59 6061 61 62 62 63 63 59 60 62 63 Attach left and right pad sections to board using screws and washers as shown. Using the holes which line up for your board size, attach center pad section to left and right sections and board using screws and washers as shown. 62 62 A. 62 63 63 62 62 63 59 60 63 62 2.1. 63 62 63 63 59 6061 61 62 62 63 63 59 60 62 63 Attach left and right pad sections to board using screws and washers as shown. Using the holes which line up for your board size, attach center pad section to left and right sections and board using screws and washers as shown. 62 62 A. 62 63 63 62 62 63 59 60 63 62 2.1. 63 62 NOTE: Part # 201580 (61) is not used on 44” acrylic backboards as shown in Figure A. 29 06/06 ID# M6611341 ID# M6611341 06/06 30 Inscrivez ici le numero de modele qui apparait sur la boite: Die Modellnummer vom Verpackungskarton hier eintragen: Escriba aqui el numero de modelo que viene en la caja: Gebrauchsanleitung fur tragbare Systeme Kundendienstzentrale • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. Manual del Propietario del Sistema Portatil Centro de Servicio al Cliente • N53 W24700 South Corporate Circle • Sussex, WI 53089 • EE.UU. AVERTISSEMENT! WARNUNG! .ADVERTENCIA! LISEZ CE MANUEL D'UTILISATION AVANT D'UTILISER CET APPAREIL SOUS PEINE DE BLESSURES OU DE DEGATS MATERIELS. DAS BENUTZERHANDBUCH VOR GEBRAUCH DIESES PRODUKTS SORGFALTIG DURCHLESEN. EIN MISSACHTEN DIESER BETRIEBSANLEITUNG KANN VERLETZUNGEN ODER SACHSCHADEN ZUR FOLGE HABEN. LEA Y ENTIENDA EL MANUAL DEL OPERADOR ANTES DE USAR ESTA UNIDAD. SI NO SE SIGUEN LAS INSTRUCCIONES DE OPERACION SE PODRIA OCASIONAR UNA LESION O DANOS A LA PROPIEDAD. Systeme portable - Manuel de l'utilisateur Service clientele • N53 W24700 South Corporate Circle • Sussex, WI 53089 • E.-U. Numer...