valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
Consult your physician before beginning any exercise program. 2. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately. Failure to do so may result in serious injury. 3. Do not allow minors or children to play on or around this equipment. 4. Exercise with care to avoid injury. 5. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. Please note: * Thank you for purchasing the Parabody 360101 Leg Press Adapter Kit. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. Tools Required for Assembly * Rubber mallet or hammer * 3/4” wrench * 9/16” wrench * Ratchet with 3/4” and 9/16” sockets * Adjustable wrench * Tape measure Bolt Length Ruler NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. BOLT LENGTH BOLT LENGTH RULER: 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 2 FIGURE 1 STEP 1 • Slide two 2” SQ. COVER CAPS (6) over the FRONT LEG (1) as shown in FIGURE 1. 1 6 PARTS LIST 3 PART # 6838003 6693902 6838103 3116201 6405201 6467001 6832701 3102501 KEY 1 2 3 4 5 6 7 8 QTY 1 1 1 2 1 2 1 6 PART # 3102802 3102933 3102910 3102937 6837801 6837901 3102502 3102801 DESCRIPTION 3/8” LOCKNUT 3/8 X 2” BOLT 1/2 X 3” BOLT 1/2 X 4-1/2” BOLT PRIMARY CABLE LEG PRESS CABLE 1/2” WASHER 1/2” LOCK NUT QTY 3 3 2 2 1 1 2 2 DESCRIPTION FRONT LEG PULLEY BRACKET BASE CONNECTION 3-1/2” PULLEY 2” SQ. END CAP 2” SQ. COVER CAP 2” SQ. RUBBER BUMPER 3/8” WASHER KEY 9 10 11 12 13 14 15 16 FIGURE 2 3 STEP 2 • Slide one 2” SQ. END CAP (5) into the BASE CONNECTION (3) as shown in FIGURE 2. FIGURE 3 7 2 STEP 3 • Attach one 2” SQ. RUBBER BUMPER (7) to the top of the PULLEY BRACKET (2) as shown in FIGURE 3. NOTE: The LEG PRESS ATTACHMENT (832101) must be assembled before connecting it to the PARABODY 375 HOME GYM 5 FIGURE 4 STEP 4 • Remove two 1/2 X 4” BOLTS, two 1/2” WASHERS, and two 1/2” LOCK NUTS from the BASE and STACK GUARD as shown in FIGURE 4. (NOTE: Discard the 1/2 X 4” BOLT.) 4 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 5 STEP 5 • Securely fasten the FRONT LEG (1) and the BASE CONNECTION (3) to the BASE and STACK GUARD using two 1/2 X 4-1/2” BOLTS (12) and two previously removed 1/2” LOCKNUTS. See FIGURE 5. STACK GUARD 1/2” WASHER 1/2 X 4” BOLT 1/2” NUT BASE BASE 12 1/2 X 4-1/2” 3 1 1/2” NUT STACK GUARD 5 STEP 6 Remove the existing CABLE (part #68331) using the following steps: • Unscrew the threaded end of CABLE from the HEAD PLATE ASSEMBLY. • Route the CABLE around the FLOATING PULLEY as shown in FIGURE 6. REMOVE CABLE • The pulleys in TOP BOOM may need to be temporarily removed to remove CABLE. • Route the CABLE through the TOP BOOM as shown in FIGURE 6. • Disconnect LAT BAR from TOP BOOM. FIGURE 6 • (NOTE: Discard CABLE part #68331) 6 STEP 7 Install the NEW PRIMARY CABLE (13) using the following steps: • Route the CABLE (13) back over one pulley in the GUIDE ROD SUPPORT, down through the PULLEY BRACKET (2) and over the second pulley in the GUIDE ROD SUPPORT. • Route the CABLE (13) around the FLOATING PULLEY BRACKET as shown in FIGURE 7. • Route the CABLE (13) through the TOP BOOM as shown in FIGURE 7. The pulleys in TOP BOOM may need to be temporarily removed to perform this step. (Note: Make sure the CABLE is running in all the pulley grooves.) FIGURE 7 2 13 • Screw the threaded end of CABLE (13) into the HEAD PLATE ASSEMBLY. IMPORTANT: Cable must run in all the pulley grooves. 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 8 7 STEP 8 • Loop CABLE (13) around one 3-1/2” PULLEY (4) in the PULLEY BRACKET (2) and SECURELY assemble using one 3/8 X 2” BOLT (10), and two 3/8” WASHERS (8) and one 3/8” LOCK NUT (9) as shown in FIGURE 8. FIGURE 9 STEP 9 • Remove one existing 3-1/2” PULLEY,two WASHERS, two 2” WHEELS and two SPACERS from the ADJUSTMENT TUBE on the 832 LEG PRESS OPTION by unfastening the 3/8 X 4-1/2” BOLT holding the pulley on. See FIGURE 9. (NOTE: The pulley will be used in STEP 12.) 3-1/2” PULLEY 2” WHEEL 3/8 X 4-1/2” BOLT SPACER 10 3/8 X 2” 9 4 2 8 8 FIGURE 10 STEP 10 • Assemble the LEG PRESS CABLE (14) to the ADJUSTMENT TUBE on the 832 using the existing previously removed 3/8 X 4-1/2” BOLTS, SPACERS, WASHERS, 2” WHEELS AND NUT. (Note: Do not overtighten! Tighten only until nut is completely on bolt.) See FIGURE 10. 2” WHEEL 3/8 X 4-1/2” BOLT NUT WASHER 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 SPACER 14 DO NOT OVERTIGHTEN! FIGURE 11 STEP 11 • Securely fasten the 832 LEG PRESS to the FRONT LEG (1) using two 1/2 X 3” BOLTS (11), two 1/2” WASHERS (15), and two 1/2” LOCK NUTS (16) as shown in FIGURE 11. 9 1/2 X 3” 11 16 1 15 10 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 12 STEP 12 • Attac...