valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
Make sure the Long Cable Trap is positioned as shown, so it will hold the Cable in place. 18 17 16 70 69 B 55 48 A 47 44 45 Axle 69 70 92 8221 85 Lubricate 77 77 51 89 7 50 6 15 21 55 A 27 27 42 10 11 22. Attach the 3 1/2” Pulley (15) and a Cable Trap (66) to the two “I”-plates (81) with a 3/8” x 2“ Bolt (12) and a 3/8” Nylon Locknut (21). Make sure the Cable Trap (66) is positioned as shown. Route the Short Cable (23) around the Pulley (15) attached to the “I”-plates in the direction shown. Route the Short Cable (23) through the first 3 1/2” Pulley (15) on the weight support arm (A). 22 21. Move to the other side of the unit. Route the Short Cable (23) around the “V”-Pulley (6) on the Right Butterfly Arm (48). Make sure the Long Cable Trap (50) is positioned as shown. Tighten the Bolt and Locknut on the pulley bracket (D). Tighten the Bolt and Locknut on the pre-assembled Pulley (15) attached to the pulley bracket (D). Route the Short Cable (23) around the Pulley in the direction shown. Make sure the Long Cable Trap (50) is positioned to hold the Cable in place. 21 20. Locate the Short Cable (23). It has a ball on one end and a threaded tip on the other. Feed the threaded end of the Short Cable (23) between the pre-assembled 3 1/2” Pulley (15) and the hook (C) on the Top Frame (55). Next, route the Short Cable around the angled “V”-Pulley (6) on the Butterfly Upright (42) and then around the “V”-Pulley (6) on the Left Butterfly Arm (47). Make sure the Long Cable Trap (50) is positioned to hold the Cable in place. If necessary, adjust the position of the Long Cable Trap. 20 55 15 23 C 47 6 50 42 50 6 48 15 D 15 15 A 23 23 19. Attach two 3 1/2” Pulleys (15) to the weight support arm (A) on the Top Frame (55) with two 3/8” x 2” Bolts (12) and two 3/8” Nylon Locknuts (21). 19 21 15 12 55 A 81 21 81 12 66 12 24. Attach a “V”-Pulley (6) and a Long Cable Trap (50) to the lower hole on the Press Upright (56) with a 3/8” x 4 1/4” Bolt (80), a 3/8” Flat Washer (9) and a 3/8” Nylon Locknut (21). Make sure the “V”-Pulley is on the indicated side of the Press Upright and that the Long Cable Trap is positioned as shown. Tighten the Bolt and Locknut on the pre-assembled “V”-pulley (6) on the Press Frame (17). 24 23. Move to the other side of the unit. Route the Short Cable (23) through the second 3 1/2” Pulley (15) on the weight support arm. Make sure the Short Cable (23) is in the groove of all Pulleys and that the Cable and the Pulleys move smoothly. Attach the Short Cable (23) to the Small “U”-Bracket (67) with a 1/4” Nylon Locknut (2) and a 1/4” Flat Washer (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing. Attach the small “U”-Bracket (67) to the Weight Tube (63) with the 5/16” x 1 3/4” Bolt (72) and a 5/16” Nylon Locknut (3). 23 23 67 72 2 23 2 67 10 50 80 6 56 17 9 21 25. Attach a 3 1/2” Pulley (15) and a Cable Trap (66) to the lower end of the Press Upright (56) with a 3/8” x 3 3/4” Bolt (71), a 3/8” Flat Washer (9) and a 3/8” Nylon Jam Nut (83). Make sure the Pulley is on the right side of the Upright and that the Cable Trap is positioned as shown. Tighten the Bolt and Locknut on the pre-assembled Pulley (15) on the Butterfly Base (4). Make sure the Cable Trap is positioned as shown. 25 71 66 56 9 83 10 3 63 15 15 6 15 4 13 27. Locate the Long Cable (58). It has a closed loop on one end and a threaded tip on the other. Attach the closed loop to the Press Upright (56) with a 5/16” x 2 3/4” Bolt (11), a 5/16” Flat Washer (8) and a 5/16” Nylon Locknut (3). Make sure the flat side of the closed loop is turned towards the Upright. Make sure the Long Cable is attached on the indicated side of the Press Upright. Route the threaded end of the Long Cable around the “V”-Pulley (6) on the P...
Questo manuale è adatto anche per i modelli :Formatori - 831.159370 (857.8 kb)
Formatori - 831.159370 (857.8 kb)
Formatori - 831.159370 (857.8 kb)
Formatori - 831.159370 (857.8 kb)