valutazioni - 0, GPA: 5
(
)
)
|
Facilità d'uso
Lire le gUIDE DU TAPIS ROULANT avant de se servir du present MANUEL D’UTILISATION. 3 ENgLISH 21 FRANcAIS 3 ASSEMBLY There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken. Before proceeding, find your treadmill’s serial number located near the on/off power switch and power cord and enter it in the space provided below. ENTER YOUR SERIAL NUMBER IN THE BOX BELOW: » Refer to the SERIAL NUMBER and MODEL NAME when calling for service. » Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card. SERIAL NUMBER: MODEL NAME: Horizon CT5.1 TrEADMiLL WArninG SERIAL NUMBER: MODEL NAME: Horizon CT5.1 TrEADMiLL WArninG 4 READING RACK WATER BOTTLE HOLDER GRIP PULSE HANDRAILS SUPPORT BAR ON/OFF SWITCH CIRCUIT BREAKER TRANSPORT WHEEL POWER CORD SPE AKE R S CONSOLE I POD /MP3 PLAYER POCKET TOUCH PAD PANEL AND DISPLAY WINDOWS SAFETY KEY PLACEMENT MOTOR COVER RUNNING BELT / RUNNING DECK SIDE RAIL ROLLER END CAP REAR ROLLER ADJUSTMENT BOLTS CONSOLE MAST FOOT LOCK LATCH (UNDERNEATH DECK) TooLS inCLUDED: PrE ASSEMBLY • Screwdriver • 6 mm T-Wrench • 5 mm L-Wrench • 4 mm L-Wrench PArTS inCLUDED: • 1 Console Assembly • 2 Console Masts • 1 Support Bar • 2 Bottom Console Covers • 5 Hardware Bags • 1 Safety Key • 1 Audio Adapter Cable • 1 Bottle of Silicone Lubricant (for 2 applications) nEED HELP? If you have questions or if there are any missing parts, contact Customer Tech Support. Contact information is located on the back panel of this manual. UnPACKinG Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock latch secure. Unpack the unit where it will be used. The enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill. WArninG DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill from packaging until specified to do so in the assembly instructions. You may remove the plastic wrap from console masts. WArninG FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY! NOTE: During assembly, do not completely tighten any screws or bolts until step 4 is complete! NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended. 5 6 ASSEMBLY STEP 1 A Cut the yellow banding straps and lift the running deck upward until the foot latch locks. Remove all contents from underneath the running deck. B Open hardware bag 1. C With the running deck in the raised position, attach the left console mast to the base frame using 4 bolts (a), 4 spring washers (b) and 4 flat washers (c). BOLT (A) 20 mm Qty: 4 SPRING WASHER (B) 15 mm Qty: 4 FLAT WASHER (C) 15 mm Qty: 4 HARDWARE BAG 1 CONTENTS : BOLTS (A) SPRING WASHERS (B) FLAT WASHERS (C) LEFT CONSOLE MAST BASE FRAME RUNNING DECK FOOT LATCH Note : Do not completely tighten any screws or bolts until step 4 is complete! 7 ASSEMBLY STEP 2 A Open hardware bag 2. B Pull lead wire through right console mast. After pulling the lead wire through the mast, the top of the console cable should be located at the top of the mast. Detach and discard the lead wire. C With the running deck in the raised position, attach the right console mast to the base frame using 4 bolts (a), 4 spring washers (b) and 4 flat washers (c). Note : Be careful not to pinch any wires while assembling the right console mast. BOLT (A) 20 mm Qty: 4 SPRING WASHER (B) 15 mm Qty: 4 FLAT WASHER (C) 15 mm Qty: 4 HARDWARE BAG 2 CONTENTS : BOLTS (A) SPRING WASHERS (B) FLAT WASHERS (C) RIGHT CONSOLE MAST CONSOLE CABLE LEAD WIRE BASE FRAME RUNNING DECK Note : Do not completely tighten any screws or bolts until step 4 is complete! 8 ASSEMBLY STEP 3 BOLT (D) 25 mm Qty: 2 FLAT WASHER (E) 16 mm Qty: 2 HARDWARE BAG 3 CONTENTS : BOLT (D) FLAT WASHER (E) CONSOLE MAST CONSOLE CABLES CONSOLE ASSEMBLE LEFT SIDE FIRST A Disengage the deck lock latch with your foot to lower the running deck. B Open hardware bag 3. C Gently place the console on top of the console masts. Attach the left side first using 1 bolt (d) and 1 flat washer (e). D Connect the console cables, carefully tucking wires in masts to avoid damage. E Attach the right side of the console using 1 bolt (d) and 1 flat washer (e). Note : Do...