valutazioni - , GPA: ( )

Istruzioni per l'uso Asus, Modello JUMPERFREE PC133

Produttore : Asus
File Size : 2.71 mb
File Nome : cuplevm-100.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

If you have more than two UltraDMA/66 devices, you will need to purchase another UltraDMA/66 cable. NOTE: The hole near the blue connector on the UltraDMA/66 cable is intentional. TIP: You may configure two hard disks to be both Masters with two ribbon cables – one for the primary IDE connector and another for the secondary IDE connector. You may install one operating system on an IDE drive and another on a SCSI drive and select the boot disk through 4.6 Boot Menu. CUPLE-VM CUPLE-VM IDE Connectors Primary IDE Connector Secondary IDE Connector NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. PIN 1 28 ASUS CUPLE-VM User’s Manual 3. HARDWARE SETUP 10) Floppy Disk Drive Connector (34-1 pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After connecting the single end to the board, connect the two plugs on the other end to the floppy drives. (Pin 5 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 5 plugged). CUPLE-VM NOTE: Orient the red markings on the floppy ribbon cable to PIN 1 PIN 1 CUPLE-VM Floppy Disk Drive Connector 11) Standard Infrared Module Connector (5-pin IR) This connector supports an optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system cases that support this feature. You must also configure the setting through UART2 Use Infrared (see 4.4.2 I/O Device Configuration) to select whether UART2 is directed for use with COM2 or IrDA. Use the five pins as shown in Back View and connect a ribbon cable from the module to the motherboard’s SIR connector according to the pin definitions. Front View Back View IR CUPLE-VM CUPLE-VM Infrared Module Connector 1 +5VIRRXIRTX (NC)GND +5V IRTX (NC) GND IRRX Connectors3. H/W SETUP ASUS CUPLE-VM User’s Manual 29 3. HARDWARE SETUP Connectors3. H/W SETUP 12) Wake-On-LAN Connector (3-pin WOL_CON) This connector connects to a LAN card with a Wake-On-LAN output, such as the ASUS PCI-L101 Ethernet card (see 7. Appendix). The connector powers up the system when a wakeup packet or signal is received through the LAN card. IMPORTANT: This feature requires that Wake-On-LAN features are enabled (see 4.4.3 Power Management) and that your system has an ATX power supply with at least 720mA +5V standby power. CUPLE-VM CUPLE-VM Wake-On-LAN Connector IMPORTANT: Requires an ATX power supply with at least 720mA +5 volt standby power. WOL_CON +5 Volt Standby Ground PME 13) Wake-On-Ring Connector (2-pin WOR) This connector connects to internal modem cards with a Wake-On-Ring output. The connector powers up the system when a ringup packet or signal is received through the internal modem card. NOTE: For external modems, Wake-On-Ring is detected through the COM port. IMPORTANT: This feature requires that Wake-On-Ring is enabled (see 4.4.3 Power Management) and that your system has an ATX power supply with at least 720mA +5V standby power. CUPLE-VM WOR 1 2 Ground RI# CUPLE-VM Wake-On-Ring Connector 30 ASUS CUPLE-VM User’s Manual 3. HARDWARE SETUP 14) CPU, Power Supply, Chassis Fan Connectors (3-pin CPU_FAN, PS_FAN, CHASS_FAN) These connectors support cooling fans of 350mA (4.2 Watts) or less. Orient the fans to blow air across the onboard heat sink. Depending on the fan manufacturer, the wiring and plug may be different. The red wire should be positive, while the black should be ground. NOTE: Rotations Per Minute (RPM) can be monitored using ASUS PC Probe. (see 6. Software Reference). WARNING! The CPU and/or motherboard will overheat if there is no airflow across the CPU and onboard heatsinks. Damage may occur to the motherboard and/or the CPU fan if these pins are incorrectly used. These are not jumpers, do not place jumper caps over these pins. GND +12V PWR_FAN Rotation Rotation CPU_FAN +12V GND Rotation CHA_FAN +12V GND CUPLE-VM CUPLE-VM 12-Volt Cooling Fan Power Connectors3. H/W SETUP ASUS CUPLE-VM User’s Manual 31 3. HARDWARE SETUP Connectors3. H/W SETUP 15) Internal Audio Connectors (4-pin CD_IN, AUX, MODEM) These connectors allow you to receive stereo audio input from such sound sources as a CD-ROM, TV tuner, or MPEG card. The MODEM connector allows the onboard audio to interface with a voice modem card with a similar connector. CUPLE-VM CD (Black) AUX (White) Right Audio Channel Right Audio Channel Ground Ground Left Audio Channel Left Audio Channel Modem-In MODEM Ground Ground Modem-Out CUPLE-VM Internal Audio Connectors 16) USB Header (10-1 pin USB2) If the USB port connectors on the back panel are inadequate, this USB header is available for two additional USB port connectors. Connect the USB headers to the 2-port USB connector set and mount the bracket to an open slot on your chassis. CUPLE-VM USBPORT GND USBP3+ USBP3– USB Power 1 5 6 10 NC GND USBP2+ USBP2– USB Power CUPLE-VM USB Port 32 ASUS CUPLE-VM User’s Manual 3. HARDWARE SETUP 17) ATX Power Supply Connector (20-pin block ATXPWR) This connector connects to an ATX power sup...