valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
• Carefully apply the side edge of the label to the side edge of the label area on the backboard. • While rubbing the label in place, continue to peel the backing from the other half of the label. • After applying the label, rub the label firmly with a cloth to make sure the label is adhered to the backboard. • Dispose of the label backing properly. Backboard Assembly 3 1 2 Side Edge Base “T” End Plug • Place the loops at the top of the net into the grooves on the ring. • Pull each loop through a ring tab, as shown. Hole Hole Rectangular Tabs Hole Rim Hole 4 Net Assembly • Place the rim on a flat surface with the rectangular tabs facing up. • Locate the four screw holes on the underside of the net assembly. • Align the four screw holes on the underside of the net assembly with the four holes in the rim. • Place the net assembly onto the rim. Groove Ring Ring Tab Groove Ring Tab 3 This product contains small parts in its unassembled state. Adult assembly is required. CAUTION Assembly 5 6 8 7 4 • While holding the ring assembly and rim together, turn them over. • Insert four screws into the holes in the rim, making sure each hole in the rim is still aligned with each screw hole in the net assembly. • Partially tighten the screws with a Phillips screwdriver. Turn the rim over to ensure that the net loops are still in the grooves and through the ring tabs before completely tightening the screws. Do not over-tighten the screws. Rim 4 5 6 Large Square Opening Base Upper Post Curved End 4 5 6 • Hook the rectangular tab on each side of the rim to the upper post, as shown. • Rotate the rim down until it snaps into place on the upper post. Push down on the rim to be sure it is secure. Rectangular Tab Rim Upper Post • Lean the rim against a wall for support. • Locate the pegs on each side of the rim and the grooves on the backboard. • Position the backboard with the Fisher-Price® logo facing up. • Place your foot on the base to hold it steady and slide the backboard onto the upper post at an angle, as far as it will go. Note: There should be no gap between the upper post and the backboard. • Move the assembly away from the wall. 6 4 5 Backboard Fisher-Price® Logo Peg Groove Wall Rim Upper Post • Position the base as shown. • Position the upper post so that the straight end is down and the curved end is up and facing away from the base. Hint: For easier assembly, apply liquid soap or rub a candle or bar soap around the bottom of the upper post (especially on the corners) and the inside of the large square opening. If assembling inside, place a tarp under the base to protect the floor surface. • Insert the upper post into the large square opening in the base and, using a circular motion, push it all the way down. Assembly 5 Fisher-Price® • Move to the side of the assembly. • Place your foot on the base to hold it steady. • Press down firmly on the lower backboard while rotating the backboard up. • When properly assembled, the pegs on the upper post rest in the grooves in the backboard, as shown. 9 Top View PULL HERE PRESS HERE Peg Peg Grooves Back View Note: The height of the rim is three feet as assembled. 6 4 5 Lower Post Rib Groove Base 10 • Align the rib on the bottom of the lower post with the groove in the opening in the base. • Insert the lower post into the opening and push down, using a circular motion, until it snaps into place. IMPORTANT! Assembly of the lower post is a permanent assembly. Hint: For easier assembly, apply a small amount of liquid soap around the bottom of the post. If assembling inside, place a tarp under the base to protect the floor surface. • Align the lever on the side of the collar with the opening in the top of the lower post. • Fit the collar onto the lower post, making sure the peg on each side of the collar snaps into the hole on each side of the post. Collar Lever Opening Lower Post Hole Peg 11 Note: The collar may already be factory assembled. • If the lever comes off, simply re-attach it. • Insert the peg on one side of the lever into the hole in the collar. • Snap the other peg in the lever into the other hole in the collar. Assembly is now complete. Please refer to assembly step 2 to fill the base with water or approximately 50 lbs. of sand (water and sand not included) to keep this product stationary. Holes Peg Peg 12 4 5 6 • As assembled, the rim height is three fee...
Questo manuale è adatto anche per i modelli :Formatori - GROW TO PRO BASKETBALL H5556 (179.11 kb)