valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
With your thumb on the tab and your first two fingers hooked into the lip (located directly across from the tab over clear window), gently lift up. 5. To close the Ice Chamber Lid, note the two hinge holes located at the top back of the Motor Base that will accept the two hinges located on the underside of the Ice Chamber Lid. Set the hinges in place as this 5 is an important step in properly repositioning and closing the lid. 6. Next, make sure the tab extrusion located at the front end of the Lid is positioned to fit into the groove located at the front inside top of the Ice Shaving Chamber. The proper insertion of the tab into the groove is mandatory in order for the ICE SHAVING BLENDER to operate. 7. The Lid should close and snap shut with the Lid fitting smoothly into place. 8. Before first use, tighten the Blade Cap by twisting firmly (see Changing the Blade for location), as it may have become loose during shipping. 9. The Water Reservoir is located at the back of the Motor Base. It is removable and snaps in and out for easy cleaning. Now you are ready to enjoy cold, refreshing margaritas and drinks from your ICE SHAVING BLENDER! HOW TO OPERATE 1. First, find a stable surface near an electrical outlet before starting. Make sure the cord is away from any water source. It is acceptable to use an extension cord if needed. 2. Fill the Pitcher with your favorite liquor, drink mix or fruit. You may choose to follow one of the recipes included in this Instruction Manual. 3. Put the Picher Lid on the Pitcher and set the Pitcher in place. 4. Set aside a dish of ice cubes and allow ice to sit for about 5-10 minutes, or until ice has slightly melted and does not have a frosty appearance. 5. Open the Ice Shaving Compartment and make sure that it is free from any foreign objects. 6. Add enough ice cubes to reach, but not pass, the max fill line. 7. Plug in unit while it is in the OFF position. 8. Turn unit on. 9. Select blending and ice shaving settings by pushing the buttons located at the bottom of the ICE SHAVING BLENDER. 10. Please note that during the first few uses, you may notice a slight graphite or burning odor. This is common with all new blenders. ENGLISH 6 ENGLISH ENGLISH HELPFUL TIPS Shaving Ice • For best results, let ice sit in a separate bowl or container for 5-10 minutes before putting in Ice Shaving Chamber. Ice should be slightly melted before shaving. • The Pitcher is able to hold more liquid than the fluid ounce measurements allow, but has been marked to prevent spillage resulting from ice shaving volume. If using the Ice Shaver, make sure to fill the Pitcher with no more than 24-ounces of liquid. Exceeding this amount will result in spillage. • Prior to each use, make sure that Blade Cap has been tightened for optimal shaving results. Odor As with most modern blending appliances, this unit has a high RPM electric motor. It is common for the motor to emit a slight graphite or burning odor for the first few uses. After the first few uses, the odor will go away. Location of Water Reservoir and Cord The Water Reservoir and cord are located at the back of the Ice Shaving Chamber. Water Reservoir Cord Location CLEANING & MAINTENANCE 1. After using your ICE SHAVING BLENDER, disconnect from electrical outlet. Remove plug by gripping the plug body and pulling out of the outlet. Never yank or twist cord to unplug the unit. 2. Thoroughly wash the clear Pitcher and Pitcher Lid, Blending Blade with Rubber Washer, Ice Tray, Ice Chamber Lid, and Water Reservoir in warm, sudsy water and thoroughly dry. DO NOT put the Motor Base in water. When needed, use a damp, non-abrasive cloth to wipe exterior. 3. Once washing and drying is complete, reassemble your ICE SHAVING BLENDER. Wind the cord and return to the convenient storage location at the back of the Motor Base. Now your ICE SHAVING BLENDER is ready to use again. (continued on next page) 7 ENGLISH Changing the BladeOnce blade becomes dull, it will need to be changed. You may also want to periodically take apart the Ice Shaving Chamber to clean all of the parts inside. To take the Blade out, follow these steps: Press Brake Bar back and up toward the Ice Shaving Chamber.1. While holding the Brake Bar turn Spinner counterclockwise 2. to unlock. Lift the Spinner to release. Carefully press tabs of Blade Housing inward and lift up.3. Twist off Blade Cap to release the Blade. USE EXTREME 4. CAUTION. BLADE IS VERY SHARP. When replacing the Spinner, make sure to press the Brake Bar back and 5. up toward the Ice Shaving Chamber while turning Spinner clockwise. SpinnerBlade CapBlade Housing Blade ENGLISH Changing the BladeOnce blade becomes dull, it will need to be changed. You may also want to periodically take apart the Ice Shaving Chamber to clean all of the parts inside. To take the Blade out, follow these steps: Press Brake Bar back and up toward the Ice Shaving Chamber.1. While holding the Brake Bar turn Spinner counterclockwise 2. to unlock. Lift the Spinner ...