valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
9. Align the enclosure with the rails, and slide it into the rack.
WARNING: The pins in the rails are load-bearing. Do not
Completing the Installation
Selecting the Enclosure Environment
remove the pins except to replace them with the pins for
1. Reinstall the components in the enclosure.
round-hole racks.
2. Connect the VHDCI connector on the controller module to
the output of an MSA1500 cs or to the external connector
Before installing the enclosure in a rack, select a location that
4. Identify the left (L) and right (R) rack rails by markings
of a sixth-generation Smart Array controller in a server.
meets the environmental requirements described in the
stamped into the rails.
HP StorageWorks Modular Smart Array 20 User Guide.
3. Connect the AC input socket of each power supply unit to
5. Slide the front end of the right rack rail toward the inside
separate AC power sources.
For adequate airflow within the rack, use appropriate high-
front of the rack until the locking latch engages with the
airflow inserts in rack cabinet doors and observe industry-
marked hole in the front rack upright.
standard practices for adequate spacing between racks or
WARNING: To reduce the risk of electrical shock or
damage to the equipment:
rows of racks.
• Do not disable the power cord grounding plug. The
For more information about setting up the rack, refer to the rack
grounding plug is an important safety feature.
user guide.
• Plug the power cord into a grounded (earthed)
electrical outlet that is easily accessible at all times.
• Unplug the power cord from the power supply to
10. Remove the mounting bracket covers (1), and tighten the
disconnect power to the equipment.
Installing the Enclosure in a Rack
thumbscrews to secure the enclosure to the rack (2).
• Do not route the power cord where it can be walked
on or pinched by items placed against it. Pay
particular attention to the plug, electrical outlet, and
1. Remove the enclosure components to reduce the enclosure
the point where the cord extends from the system.
weight and make it more manageable.
4. Press the enclosure power button on the rear of the unit.
WARNING: The enclosure weighs 24 kg (53 lb) when full,
5. Confirm that the enclosure components are all functioning
and 9 kg (20 lb) when the components have been
normally by observing the condition of their status LEDs,
removed. Use two people to move an enclosure or to
6. Extend the back end of the rail toward the inside rear of
which should all be green. If the amber LED on any
install one in a rack.
the rack until the locking latch engages with the marked
component is illuminated, the component needs attention.
hole in the rear rack upright.
2. Use the rack mounting template as a guide to mark where
For detailed information about the meaning of different
in the rack the rails for the enclosure are to be located.
LED illumination patterns, refer to the HP StorageWorks
Modular Smart Array 20 User Guide.
a. At the front of the rack, with the front of the template
facing you, align the lower edge of the template with
Installation is complete.
the bottom of the rack (or the top of the previous rack
component). Be sure that the lower edge of the
template is level.
11. Replace the mounting bracket covers.
b. Push the template tabs into the holes in the rack uprights
to hold the template in place.
12. If you intend to move the rack while the enclosure is
installed, adjust the shipping brackets on each rail to
secure the enclosure in the rack.
a. Loosen the shipping bracket locknut (1).
b. Slide the bracket forward until it engages with the
enclosure chassis (2).
7. Loosen the locknut on the shipping bracket (1), and move
the bracket to the rearmost position on the rail (2).
c. Use a marker pen to indicate the holes in the rack
uprights into which the scissor-like locking latches are to
be inserted, as specified by the template.
d. Repeat these steps to mark the back of the rack, using
the information on the back of the template as a guide
to the required location of the locking latches in this
c. Tighten the locknut.
case.
d. Repeat this procedure for the other rail.
3. If the holes in the rack uprights are round instead of
square, remove the standard pins from the rails and
replace them with the round-hole pins provided in the rack
8. Repeat steps 5 through 7 for the left rack rail.
mounting hardware kit.