valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
connected to your network, and iLO addresses
configured appropriately.
Completing initial configuration
NOTE:
HP BladeSystem c-Class KVM Interface
After the servers reboot, continue the configuration
Adapters are not supported.
using the first node. A default Windows Administrator
The server from which you choose to perform the
password (HPinvent!) has been set and this is used
configuration will be designated the first node. The
to log on automatically. Leave this Windows
other server will be designated the second node.
Administrator password unchanged until you are
For instructions on using each access method, see the
prompted for a new password in a later configuration
HP StoreEasy 5000 Storage Administrator Guide or
step. On logon, the HP ICT window is launched
the HP Integrated Lights-Out User Guide.
automatically.
Use the HP ICT to perform setup tasks such as setting
the time zone, network configuration, changing the
computer name, joining a domain, and creating the
Set up Windows and discover second
cluster. To create a cluster, each server will need
node
network connectivity to the domain controller and a
When the storage system starts, the servers will begin
DNS server.
a first time setup procedure that takes approximately
IMPORTANT:
HP strongly recommends that
10–15 minutes, including the Set Up Windows wizard.
you validate your configuration when using
Use only one server node (blade) to complete the setup
clusters. Whether you create a cluster through
procedure.
the ICT or the Failover Cluster Manager, one of
NOTE:
Your storage system comes
the first steps is validating your configuration
pre-installed with the Microsoft Windows
using the Microsoft cluster validation tool. If you
Storage Server 2012 Standard Edition
choose to skip the validation step, you can still
operating system. No operating system
validate the cluster after it is created.
installation is required.
After the storage system installation process is
In the Set Up Windows wizard, you are asked to
complete, you can use the browser (iLO) and remote
choose a language, country, and keyboard. After you
desktop methods to access and configure the storage
accept the EULA, the server you are connected to
system. See the HP StoreEasy 5000 Storage
attempts to discover the second server. This is done
Administrator Guide for more information about using
over the internal switch (3, Figure 2 (page 1)). If the
these access methods.
second server is not ready, you may see a message
IMPORTANT:
Be sure to install any available
stating Cannot establish communication
software updates. You can be notified of
with the second node. Click Retry to attempt
updates by subscribing to the HP Driver,
discovery, and repeat the retry until the second node
Support, and Security alerts e-mail list:
is discovered.
1.
Go to http://www.hp.com/go/
After the second node is discovered, there will be a
StoreEasy5000.
few more installation steps that occur automatically on
2.
Select Technical Support/Manuals.
each server, and then both servers will reboot.
3.
On the product page that appears, select
NOTE:
If you click Cancel instead of Retry,
Signup: driver and support alerts.
you must access the second node from iLO or
To manually check for updates, perform steps
a local I/O diagnostic (SUV) cable and
1 and 2. On the product page that appears,
manually follow the Set Up Windows wizard
select Download drivers and software. Select
on the second node. Because the discovery
your StoreEasy 5000 product and then select
process was not completed, there will also be
the operating system. A list of available
an extra step later to establish a connection
downloads is displayed.
between the two nodes. You will find instructions
for this, if needed, in the online help of the Initial
HP strongly recommends that you also install Insight
Configuration Tasks (ICT).
Remote Support as described in the HP StoreEasy
5000 Storage Administrator Guide.
Page 5
... Questo manuale è adatto anche per i modelli :
dati dispositivi di elaborazione - HP StoreEasy 5530 10.8TB SFF 10K Storage/S-Buy (320.27 kb)
dati dispositivi di elaborazione - HP StoreEasy 5530 10TB LFF 7.2K Storage (320.27 kb)
dati dispositivi di elaborazione - HP StoreEasy 5530 10TB LFF 7.2K Storage/S-Buy (320.27 kb)
dati dispositivi di elaborazione - HP StoreEasy 5530 16.2TB SFF 10K Storage (320.27 kb)