valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
HP StorageWorks X1800sb G2
Blade signal
Intercon-
Intercon-
Notes
nect bay
nect bay
Network Storage Blade Quick
Overview
label
Start Guide
Installation of the X1800sb G2 Network Storage Blade requires the
• Four port cards
following steps:
• Ports 1 and 3 con-
Mezzanine 2
3, 4
nect to bay 3
1.
Install and configure an HP BladeSystem c-Class enclosure.
• Ports 2 and 4 con-
2.
Install any network storage blade options.
nect to bay 4
3.
Install interconnect modules in the enclosure.
4.
Connect the interconnect modules to the network.
For detailed port mapping information, see the HP BladeSystem enclosure
installation poster or the HP BladeSystem enclosure setup and installation
5.
Install the network storage blade(s).
guide on the HP website
6.
Complete the network storage blade solution configuration.
(http://www.hp.com/go/bladesystem/documentation).
Figure 1 Interconnect bay numbering and device mapping (c7000
enclosure)
IMPORTANT:
Connecting to the network
.
The HP StorageWorks Storage System Recovery DVD is included
To connect the HP BladeSystem to a network, each enclosure must be
with the X1800sb G2 Network Storage Blade. This DVD is used
Blade signal
Interconnect bay
Interconnect bay
configured with network interconnect devices to manage signals between
to restore the system to factory defaults. Keep this DVD in a safe
label
the blades and the external network.
place.
NIC 1 (embedded)
1
Two types of interconnect modules are available for HP BladeSystem
c-Class enclosures: Pass-thru modules and switch modules. For more
NIC 2 (embedded)
2
information about interconnect module options, see the HP website
(http://www.hp.com/go/bladesystem/interconnects).
Installing an HP BladeSystem c-Class
Mezzanine 1
3 and 4
enclosure
Mezzanine 2
5 and 6
Installing the X1800sb G2 Network
Before performing any blade-specific procedures, install an HP
7 and 8
Storage Blade
BladeSystem c-Class enclosure.
The most current documentation for network storage blades and other
© Copyright 2010 Hewlett-Packard Development Company, L.P.
HP BladeSystem components is available at the HP website
IMPORTANT:
(http://www.hp.com/go/bladesystem/documentation).
First edition: November 2010
If your product is factory-integrated, the blades are pre-installed
Documentation is also available in the following locations:
in the enclosure.
The information in this document is subject to change without notice.
• Documentation CD that ships with the enclosure
Microsoft, Windows, Windows XP, and Windows NT are U.S.
• HP Business Support Center website (http://www.hp.com/support)
registered trademarks of Microsoft Corporation.
• HP Technical Documentation website (http://docs.hp.com)
CAUTION:
www.hp.com
To prevent improper cooling and thermal damage, do not
Installing network storage blade options
operate the network storage blade or the enclosure unless all
hard drive and device bays are populated with either a
Before installing and initializing the network storage blades, install any
component or a blank.
options, such as an additional mezzanine card. For network storage
blade options installation information, see the HP ProLiant BL460c G7
Server Blade User Guide on the Documentation CD or on the HP website
(http://www.hp.com/go/bladesystem/documentation).
Figure 2 Interconnect bay numbering and device mapping (c3000
Installation locations with the optional SB40c
enclosure)
Storage Blade
.
Installing interconnect modules
The SB40c Network Storage Blade is an optional storage component
Blade signal
Intercon-
Intercon-
Notes
that can be used in conjunction with the X1800sb G2 Network Storage
nect bay
nect bay
Blade. If you have purchased optional SB40c Network Storage Blades,
For specific steps to install interconnect modules, see the documentation
label
the SB40c blades must be installed adjacent to X1800sb G2 Network
that ships with the interconnect module.
Storage Blades as server blade/storage blade pairs. In the figures below,
To support network connections for specific signals, install an interconnect
NICs 1 and 2
1
the proper server blade/storage blade pair installation locations are
module in the bay corresponding to the embedded NIC or mezzanine
(embedded)
shown as device bays 1 and 2, 3 and 4, and so on.
signals.
Four port cards connect
If you have not purchased the optional SB40c Storage Blade, the
Mezzanine 1
2
to bay 2
X1800sb G2 Network Storage Blades can be installed in any available
*5697-0609*
enclosure device bay.
...