valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
IRONING WITH EXTRA STEAM For a penetrating burst of steam to iron faster and to smooth difficult 5 wrinkles, firmly depress the burst of steam button. Between the individual bursts of steam, pause for at least 5 seconds to let the iron reheat for maximum additional steam. If water drops escape as you use the burst of steam, turn the temperature control dial to a slightly warmer setting and wait for the ready light to go out. wrinkles, firmly depress the burst of steam button. Between the individual bursts of steam, pause for at least 5 seconds to let the iron reheat for maximum additional steam. If water drops escape as you use the burst of steam, turn the temperature control dial to a slightly warmer setting and wait for the ready light to go out. USING THE SPRAY BUTTON For a mist of water to moisten dry and difficult fabrics such as linen, cotton or wool, or to handle stubborn wrinkles, press the spray button. The spray function is also handy to moisten creases accidentally ironed in the fabric. AUTOMATIC SAFETY SHUT-OFF As a built-in safety measure, the iron is programmed to shut-off automatically after 15 minutes. When the iron shuts off, the reset button located on top of the iron handle will come on. If you wish to resume ironing, simply push the reset button. The light will go out and the iron will re-energize immediately. Diagram 4. FILLING THE WATER TANK 1. Unplug the iron before filling. 2. Turn the variable steam dial to the lowest setting. Diagram 3. 3. Hold the iron upright but slightly tipped. 4. Using a measuring cup, slowly pour water into the water fill hole opening. Diagram 5. 5. Check see-through water reservoir to see if iron is filled to maximum fill line. Diagram 6. Note: Your iron is designed to use tap water. However, if your water is very hard, it is recommended you use distilled water. DO NOT use water from home water softening systems because such water may contain minerals that may harm the iron. EMPTYING THE WATER TANK The water tank should be emptied after each use. To do so: 1. When finished, turn temperature control dial to MIN, lowest setting, and unplug the iron from the electrical outlet. 2. While the iron is still warm, hold the iron over a sink and allow the iron to drain by tipping the point of the iron down. 3. Gently shake the iron to loosen any water drops that may be trapped. The warmth of the iron should dry out any remaining water. Note: If you empty the water tank after the iron has cooled, set the iron in an upright position on its heel, plug it in and set the temperature dial to maximum heat for 2 minutes. Then unplug the iron and let it cool before storing it. 6 DIAGRAM 6 DIAGRAM 7 SELF-CLEANING/FLUSHING Flushing the iron is advised after every 5 usages to prevent harmful mineral build-up that can clog the iron and prevent it from heating and steaming properly. To flush the iron: 1. Position temperature control dial to MIN, lowest setting. Diagram 2. 2. Turn variable steam dial to the lowest setting. Diagram 3. 3. Fill the iron’s water tank to its maximum fill line. Diagram 6. 4. Plug the iron in and set the temperature control dial to its highest setting or cotton/linen. Let it heat for 2 minutes. 5. Turn the variable steam dial counter clockwise to the highest setting. 6. Place a hand towel over the ironing surface. 7. Hold the iron horizontally 2 inches above the towel allowing steam to flow through the vents until the water tank is emptied. You may also depress the burst of steam button several times remembering to pause about 5 seconds between bursts to allow the iron to reheat. While the iron is still warm, hold the iron over a sink and allow the iron to drain by tipping the point of the iron down. 8. Pass the iron over a damp cloth to clean the soleplate or use hot iron cleaner. 9. When finished, turn temperature control dial to MIN, lowest setting, and unplug. Allow iron to cool before cleaning the exterior of the iron or storing. Use a cloth to wipe off exterior of iron before storing. STORING THE IRON Remove the cord from the outlet by grasping the plug rather than pulling the cord, and allow iron to cool. EMPTY the water tank after each use, then wrap the cord around the cooled iron as shown. Diagram 7. Allow the iron to COOL COMPLETELY before putting it away. To protect the soleplate, place the iron in an upright position on its heel. 7 CLEANING AND CARE CAUTION: Unplug the iron from the electrical outlet before cleaning the exterior of the iron and storing. Never immerse an appliance in water. CLEANING AND CARE CAUTION: Unplug the iron from the electrical outlet before cleaning the exterior of the iron and storing. Never immerse an appliance in water. If starch or other residues cling to the soleplate, use hot iron cleaner according to directions. Note: DO NOT put any chemical cleaning agents or solvents in the water tank. IMPORTANT: Any servicing that requires disassembly must be performed by an authorized service center. SERVICE INFORMATION Plea...
Questo manuale è adatto anche per i modelli :Ferri - 3314CAN (56.89 kb)