valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
The Power Indicator will blink to let you know that the iron has stopped heating. IMPORTANT: The Power Indicator will continue to blink until the iron is unplugged or reset. TO RESET THE IRON: Move the iron back and forth and allow it to reheat for 2 minutes. The indicator will stop blinking and the iron will start heating again. WARNING: Motion Smart® Auto-Off is a safety feature, not a recommended means for turning your iron off. See “Caring for Your Iron After Use” for information on turning off your iron and storing it safely between use. CARING FOR YOUR IRON AFTER USE TURNING OFF YOUR IRON: Turn the Steam Lever to (Dry) and Fabric Select Dial to Off and unplug the iron from the power source. WARNING: NEVER yank the power cord when unplugging the iron. This can damage the cord. STORING YOUR IRON 1. Turn off iron following instructions above. Allow the iron to cool. 2. If you do not use your iron on a daily basis, empty the water reservoir after each use for a longer iron life. To do so, unplug the iron, turn the iron upside down, open the fill hole cover, and allow water to flow from the fill hole. Shake the iron gently to remove trapped water drops. 3. If your iron does not have a retractable cord, loosely loop the power cord around the heel rest and store the iron on its heel rest. IMPORTANT: Wrapping the cord around the iron too tightly can damage the cord. MAINTAINING YOUR IRON CLEANING THE SOLEPLATE: Turn off iron following instructions above. Clean the soleplate if starch or other residue accumulate. TO CLEAN THE SOLEPLATE: Do not immerse the iron in liquids. Allow the iron to cool and then wipe it with a soft, damp cloth. WARNING: DO NOT use abrasive cleansers, scouring pads or vinegar to clean the soleplate. This will damage the finish. Run the iron over an all-cotton cloth to remove any residue. USING THE SELF-CLEANING FEATURE: You should use the Self-Cleaning feature once a month to maintain the optimal performance of your iron. TO USE THE SELF-CLEANING FEATURE: Turn off iron following instructions above. 1. Move the Steam Lever back and forth several times to remove debris and minerals from the Steam Valve. This keeps water flowing into the steam chamber. 2. Fill the water reservoir with tap water to the MAX line. 3. Plug in the iron, set the Fabric Select Dial to Linen and allow the iron to heat for 2 minutes. 4. Unplug the iron. 5. Hold the iron over a sink in a horizontal position. WARNING: Be careful not to touch the iron’s hot surfaces. 6. Press the Self-clean Button and hold. Water will begin dripping from the steam vents. Slowly rock the iron side to side and front to back for 30 seconds. When rocking the iron, dip the nose of the iron slightly below the rear of the iron to make certain the water circulates completely. Release the Self-clean Button after one minute. 7. Open the fill cap, turn the iron upside down, and allow the remaining water to flow out of the fill hole. 8. Dry the soleplate with a towel. 9. Plug in the iron and set the Fabric Select Dial to Linen. Let the iron heat for 2 minutes to dry out the iron completely. 10. Set the Fabric Select Dial to the Off, unplug the iron, and allow it to cool. ANTI-CALCIUM SYSTEM (select models only) The iron houses an anti-calcium filter in the reservoir, which eliminates impurities from the water. This is a permanent system located inside the water reservoir. TO PROLONG THE EFFICIENCY OF THIS FILTER, FOLLOW THESE STEPS OCCASIONALLY: 1. Unplug the iron and allow it to cool. 2. Locate the water cup that accompanied the iron. Fill it with water . full. Add 1 teaspoon of salt to water and fill the water reservoir with this solution. 3. Leave the solution in the water reservoir for 15 minutes, shaking occasionally, and then empty it. 4. Fill the water reservoir a second time with the salt water solution, shaking occasionally and empty it again after 15 minutes. 5. Fill the tank with fresh water to rinse and empty. PARA LLENAR EL TANQUE DE AGUA (use agua de grifo) 1. Asegurese de que la plancha este desenchufada. Ponga la palanca de vapor en (Dry) ( [Seco]) y la perilla de seleccion de telas en Off (Apagado). 2. Levante la Tapa del Orificio del Tanque de Agua. La tapa se puede retirar y se puede volver a colocar cuidadosamente en las ranuras. 3. Llene la taza con agua. Vierta el agua en el tanque de agua de la plancha. No llene el tanque de agua mas alla del nivel maximo de llenado. ADVERTENCIA: Para prevenir el riesgo de quemaduras, tenga cuidado al llenar una plancha caliente con agua. Las partes de metal calientes, el agua caliente y el vapor pueden causar lesiones. PLANCHANDO EN SECO 1. Asegurese de que la palanca del vapor este en la posicion (Dry) ( [Seco]). 2. Enchufe el cable en un tomacorriente de CA de 120 voltios. (En Mexico, 127 voltios.) 3. Gire el Disco Selector de Tela (Fabric Select) en la posicion deseada para planchando en seco y deje que la plancha se caliente durante 2 minutos. Mientras la plancha se esta calentando, as...