valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
1 EnGlish Problem Cause Solution Theironhasnotbeenswitchedon.Makesuretheironswitchissetto‘on’. Smoke comes out of my new iron when I switch it on. Some par ts of the appliance have been lightly greased in the factor y and may initially give off some smoke when heated. This phenomenon is perfectly normal and will cease after a shor t while. The iron does not produce any steam. The steam tank and/or the iron may not be switched on. Set both the iron switch and the steam tank switch to ‘on’. There is not enough water in the water tank. Fill the water tank (see chapter ‘Preparing for use’). The steam tank has not heated up sufficiently. Wait for 6 to 8 minutes for the steam tank to heat up. The selected ironing temperature is too low for steam ironing. Select a temperature of 2 or higher. When the iron has been set to a ver y high temperature, the steam produced is dr y and hardly visible. It will be even less visible when the ambient temperature is relatively high and it will be entirely invisible when the temperature has been set to MAX. Set the iron to a lower temperature, e.g. 2, to check if the iron is actually producing steam. Water droplets come out of the soleplate. The temperature dial may be set to a temperature that is too low for steam ironing. Select an ironing temperature that is suitable for steam ironing (temperature settings 2 to MAX). You may not have switched on the iron. Set the iron switch to ‘on’ and wait until the iron is hot. You may have placed the steam tank on an unstable and/or uneven surface. Place the steam tank on a stable and even surface. When you star t steam ironing and when you have stopped steam ironing for a while, the steam that was still present in the supply hose will have cooled down and condensed into water, which causes water droplets to come out of the soleplate. This is perfectly normal. Hold the iron over an old cloth and press the steam activator. The cloth absorbs the drops. After a few seconds, the steam production normalises. Water droplets come out of the soleplate when I use the steam boost function Steam may have condensed in the hose, the temperature may have been set below 3 or the appliance may not be ready for steam ironing. Make sure the temperature is set to 3 or higher. Steam iron for a few seconds before you use the steam boost function. (GC6360 only). EnGlish 1 Problem Cause Solution Flakes and impuritiescomeoutofthesoleplate. Theironisnew.Thisisnormal.Theparticlesareharmlessansstopcomingoutofthesoleplatewhenyouhaveusedtheironafewtimes. The soleplate is dir ty. You may have ironed at a temperature that is too high. Clean the soleplate with a damp cloth. Select the recommended ironing temperature. Impurities or chemicals present in the water have deposited in the steam vents and/or on the soleplate. Clean the soleplate with a damp cloth. Dir ty water comes out of the soleplate. Too much scale and minerals have accumulated inside the steam tank. Rinse the steam tank. See chapter ‘Cleaning and maintenance’. Steam escapes from the filling hole area during ironing. You may not have tightened the steam tank cap properly or you have spilled some water round the filling hole. Switch off the appliance and let it cool down. Remove the steam tank cap, wipe away the water round the filling hole and tighten the steam tank cap again.Then switch the appliance back on. Wet spots appear on the garment during ironing. The wet spots that appear on your garment after you have steam ironed for some time may be caused by steam that has condensed onto the ironing board. Iron the wet spots without steam for some time to dr y them. If the underside of the ironing board is wet, wipe it with a piece of dr y cloth. To prevent steam from condensing onto the ironing board, use an ironing board with a wire mesh top. 1 Gambaran umum (Gbr. 1) indonEsia 1 Gambaran umum (Gbr. 1) indonEsia A Selang pasokan B Lampu suhu C Tombol suhu D Aktivator uap E Tombol semburan uap F Tutup tangki uap G Dudukan Setrika H Tangki uap I Kabel listrik J Lampu uap-siap pakai (hanya GC6360) K Saklar tangki uap dengan lampu power-on L Kontrol uap M Saklar setrika dengan lampu power-on N ’Lampu tangki uap kosong’ (hanya GC6360) O Tapak setrika Penting Bacalah buku petunjuk ini secara saksama sebelum Anda menggunakan alat dan simpan untuk referensi di kemudian hari. , , , ,, , ,, ,, ,, , , , , Periksa apakah tegangan listrik yang tertera pada pelat sesuai dengan tegangan listrik setempat sebelum Anda menghubungkan alat ini. Jika alat dilengkapi dengan steker yang di-arde, steker ini harus dimasukkan ke stopkontak dinding yang juga di-arde. Jangan menggunakan alat jika steker, kabel, selang pasokan atau alat itu sendiri menunjukkan kerusakan yang dapat dilihat atau jika alat pernah terjatuh atau bocor. Periksalah kabel dan selang pasokan secara teratur, kalau-kalau ada kerusakan. Jika kabel listrik atau selang pasokan rusak, harus diganti oleh Philips, pusat servis resmi Philips atau orang yang mempunyai ke...
Questo manuale è adatto anche per i modelli :Ferri - GC6340/02 (2.07 mb)