valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Intelligent steam (depending on model) This system has intelligent steam control, which, after releasing the steam release button (15), provides a small amount of additional steam. The additional steam can always be stopped by briefly pressing the steam release button once again. Auto shut-off (depending on the model) If during ironing the steam release button (15) on the handle of the iron is not pressed for a certain length of time (8 minutes), the steam station will automatically switch off. The “Auto shut-off” pilot lamp (7) will flash when auto shut-off has been activated. To switch the steam station back on, press the steam release button again, and wait until the “Auto shut-off” pilot lamp remains lit continuously. Cleaning & Maintenance Always unplug the appliance from the mains supply before carrying out any cleaning or maintenance operation on it. 1. After ironing, pull out the plug and allow the appliance to cool down before cleaning. 2. Wipe the housing, handle and iron body with a damp cloth. 3. If the soleplate is soiled with dirt or scale, clean it with a damp cloth. 4. Never use abrasive products or solvents. Storing the appliance (D) 1. Always allow the appliance to cool down before storing it. 2. Set the main power to the “0” position and disconnect the mains cable. 3. Place the iron on the iron pad, standing on the soleplate. 4. Empty the water tank and store the mains cable on the cord rewind facility. Tidy the steam hose on the handle of the iron using the cord clip provided (12). Do not wrap the cords too tight. Fabric protection soleplate cover (E) (depending on the model) The fabric-protection soleplate cover is used for steam- ironing delicate garments at maximum temperature without damaging them. Use of the soleplate cover also does away with the need for a cloth to prevent shine on dark materials. It is advisable to first iron a small section on the inside of the garment to see if it is suitable. To attach the soleplate cover to the iron, place the tip of the iron into the end of the soleplate cover and pull the elastic strap over the lower rear of the iron until it fits tightly. To release the soleplate cover, pull the elastic strap and remove the iron. The fabric-protection soleplate cover may be purchased from the customer service or specialist shops: Accessory code (After-sales) Name of accessory (Specialist outlets) 464846 TDZ2510 464745* TDZ2520* * Cork handle iron “Calc‘n clean” (F) Cleaning the Boiler To extend the life of your steam generator and to avoid any build up of scale, it is essential that you rinse out the boiler after several hours of use (approximately after 50 hours). If the water is hard, increase the frequency. en en Do not use descaling agents for rinsing out the boiler, as they could damage it. 1. Check that the appliance is cold and unplugged for more than 2 hours, and that the removable water tank (1) is empty. 2. Place your appliance on the edge of your kitchen sink. 3. Remove the plastic cover located on the bottom of the appliance by turning it to the position. 4. Unscrew the boiler drainage plug located on the bottom of the appliance using a coin. 5. Holding your steam generator in upside down position, and using a jug, fill the boiler (in the base unit) with 1/4 litre of water 6. Shake the base unit for a few moments and then empty it completely over a sink or bucket. To obtain the best result, we recommend that this operation is done twice Important: before re-closing, make sure no water remains in the boiler. 7. Replace and tighten up the boiler drainage plug with a coin. 8. Insert and close the plastic cover by turning it to the position. Automatic clean warning (depending on model) Pilot light (8) will flash indicating that boiler must be rinsed. To do this, follow the procedure described in the section above. To reset “Calc‘n clean” pilot light and counter, switch the station off twice, keeping it off during at least 30 seconds each time Trouble shooting Rinsing the iron steam chamber (G) This procedure helps to remove scale particles out of the steam chamber. Carry it out approximately every 2 weeks, if the water in your area is very hard. a) Ensure that the iron is cooled down. b) Set the temperature selector (13) of the iron to the “min” position. c) Fill the tank with tap water. d) Plug in the mains cable and set the main power switch (6) to the “I” position. e) Wait until the “steam ready” indicator lamp (7) lights up. f) If the steam station has steam regulator (3), set it to the maximum position (“10”). g) Hold the iron over the sink or a container to collect the water. h) Press the steam release button (15) and gently shake the iron. Boiling water and steam will come out, carrying scale and or deposits that might be there. This could take approximately 5 minutes. i) Set the temperature selector (13) of the iron to the “max” position, without pressing the steam release button (15). The water in the steam chamber will start evaporating. ...