valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Note: If you work with the “Energy saving” function, the variable steam regulation and temperature regulation can still be used as recommended. “secure” auto shut-off (model dependent) If during ironing, the steam release button (13-14*) on the iron handle is not pressed for a certain length of time (8 minutes), the steam station will automatically switch off. The “ ” icon will flash when auto shut-off has been activated. To switch the steam station back on, press the steam release button again. Fabric protection soleplate cover (E) (model dependent) The fabric-protection soleplate cover (17*) is used for steam ironing delicate garments at maximum temperature without damaging them. Use of the soleplate cover also does away with the need for a cloth to prevent shine on dark materials. It is advisable to first iron a small section on the inside of the garment to see if it is suitable. To attach the soleplate cover to the iron, place the tip of the iron into the end of the soleplate cover and pull the elastic strap over the lower rear of the iron until it fits tightly. To release the soleplate cover, pull the elastic strap and remove the iron. The fabric-protection soleplate cover may be purchased from our customer service or from our website: Accessory code Name of accessory (After-sales) (Online shop) 571510 TZ20450 Descaling the filter and the boiler (F) (calc’nClean Plus) To extend the life of your steam generator and to prevent any build up of scale, it is essential that you rinse out the filter (12) and the boiler after a period of use. If the water is hard, increase the frequency. Do not use descaling agents for rinsing out the boiler, as they could damage it. If the “ ” icon flashes, this indicates that the boiler must be rinsed. Please proceed as follows: 1. Check carefully that the appliance is cold and unplugged for more than 2 hours, and that the water tank (1) is empty. 2. Fix the iron to the base by inserting the tip of the iron into the front slot and moving the secureLock lever (10) against the heel of the iron. 3. Place your appliance over a sink or bucket. 4. Lean the appliance on the opposite side of the filter opening. 5. Unscrew the filter (12) and take it out. 6. To wash the filter, you may: a. Place the filter under the water tap and wash it until calc residues are removed. Squeeze the filter as indicated in the picture F. b. Immerse the filter in tap water (250 ml) mixed with a measure (25 ml) of descaling fluid. Rinse filter thoroughly before placing it back into the boiler The descaling fluid can be obtained from our After- sales service or from our website. Accessory code Name of accessory (After-sales) (Online shop) 311144 TZ11001 en en 7. Holding your steam generator in the lateral position and using a jug, fill the boiler with 1/4 litre of water and replace the filter. 8. Shake the base unit for a few moments, unscrew the filter again and empty the boiler completely over a sink or bucket. For best results, we recommend that this operation is performed twice. Important: before re-closing, make sure no water remains in the boiler. 9. Replace and tighten the filter. To reset the “Clean” counter, switch the steam station on and off twice, keeping it off for at least 30 seconds each time. (on > 30s off > on > 30s off > on) Rinsing the iron steam chamber (G) Caution! Risk of burns! This procedure helps to remove scale particles from the steam chamber. Perform approximately every 2 weeks, if the water in your area is very hard. a) Ensure that the iron has cooled down. b) Set the temperature to the setting. c) Fill the tank with tap water. d) Plug in the mains cable and set the main power button (9) to the “I” position, (illuminated in red). e) Set the steam setting to and wait until the icon stops flashing. f) Hold the iron over the sink or a container to collect the water. g) Press the steam release button (13) and gently shake the iron. Boiling water and steam will be released, carrying scale and/ or deposits that might be inside. This process may take from 5 up to 10 minutes. Please note that if you have filled the water tank to the maximum, you do not have to continue until it is completely empty, but just long enough so that there are no more scale deposits appearing from your iron hand set. h) Set the temperature to the setting, without pressing the steam release buttons (13-14*). The water in the steam chamber will start evaporating. Wait until all the water inside the chamber has been evaporated. i) To clean the soleplate, immediately rub off any residue by running the hot iron over a dry cotton cloth. Recommended accessory The SL45 steam station produces a high amount of steam for best performance. Therefore, the best additional accessory would be the Siemens active-ironing board TN10100 / TN10200. Cleaning & Maintenance Attention! Risk of burns! Always unplug the appliance from the mains supply before carrying out any cleaning or maintenance operation on it. 1. After ironing, d...
Questo manuale è adatto anche per i modelli :Ferri - TS45300/01 (4.21 mb)
Ferri - TS45359/01 (4.21 mb)